Dimensions of the CE Smith V-Wing Bolster Bracket # CE26244G

Question

Question:

I need exact measurements on this product CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers - Galvanized Steel - Qty 1

asked by: Ricky

0

Expert Reply:

The CE Smith V-Wing Bolster Bracket # CE26244G that you referenced 15-1/2" long x 3" wide x 6" tall with mounting slot dimensions of 7-1/2" long x 1/2" wide.

If you need further dimensions feel free to email me back with what you need and I'll get them for you.

expert reply by: Jameson C

0

click to enlarge

Answer 1

You probably could make 2x4 bunks work on the CE Smith V-Wing Bolster Bracket #CE26244G but ideally you are going to want to use the taller boards like a 2x6 or 2x8.

view full answer...

Answer 2

I recommend the V-Wing Bolster Bracket for Pontoon Boat Trailers #CE26265G40. They are galvanized and allow for 4" wide bunk boards. These are sold individually so be sure to order enough for your application. I also recommend the Bunk Style…

view full answer...

Answer 3

The CE Smith Bolster Bracket for Pontoon Boat Trailers part #CE10052-32G does not have a listed weight capacity per the manufacturer. The reason for this is because the weight of most pontoon boats is pretty standard so I don't believe you will…

view full answer...

Answer 4

It sounds like you are trying to bring the boat down closer to the trailer frame. I have personally not seen many setups that involve using keel rollers like the CE Smith Deep V Keel Roller Assembly part #CE10455G with a pontoon boat but if you have…

view full answer...

Answer 5

Pressure treated lumber can be used for bunk boards along with bunk carpet like the #CE11349. However, it is possible that some corrosion may occur from the chemicals in the lumber over time. The CE Smith bunk boards like #CE27840 are made from…

view full answer...

Answer 6

There really is no specific bunk board size recommendation to use with the CE Smith Bolster Bracket #CE10052-32G. It really just boils down to what works best for your application. Attached is a photo that a customer sent in where it looks like they…

view full answer...

Answer 7

The end to end span of the CE Smith Bolster Bracket #CE10052-32G for Pontoon Boat Trailers is 15.03 inches, which, according to CE Smith is the most important measurement when talking about pontoon trailer brackets. CE Smith cannot guarantee these…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Dimensions of the CE Smith V-Wing Bolster Bracket # CE26244G

Product Page this Question was Asked From

Continue Researching