Why Does the CE Smith Bolster Bracket for Pontoon Boat Trailers Not Have A Weight Capacity

Question

Question:

Item # CE10052-32G What is the load capacity for this item? I am trying to adapt a ski boat lift to accommodate a pontoon.

asked by: Ken E

0

Expert Reply:

The CE Smith Bolster Bracket for Pontoon Boat Trailers part # CE10052-32G does not have a listed weight capacity per the manufacturer. The reason for this is because the weight of most pontoon boats is pretty standard so I don't believe you will have an issue. If you need some sort of metric to gauge capacity, the bracket is made of 3/8" thick steel. I took a look at the reviews and there were almost no mentions of weight being a factor. The more you use however, the more support you will have.

expert reply by: Conner L

0

Answer 1

There really is no specific bunk board size recommendation to use with the CE Smith Bolster Bracket #CE10052-32G. It really just boils down to what works best for your application. Attached is a photo that a customer sent in where it looks like…

view full answer...

Answer 2

It sounds like you are trying to bring the boat down closer to the trailer frame. I have personally not seen many setups that involve using keel rollers like the CE Smith Deep V Keel Roller Assembly part #CE10455G with a pontoon boat but if you have…

view full answer...

Answer 3

The end to end span of the CE Smith Bolster Bracket #CE10052-32G for Pontoon Boat Trailers is 15.03 inches, which, according to CE Smith is the most important measurement when talking about pontoon trailer brackets. CE Smith cannot guarantee these…

view full answer...

Answer 4

Pressure treated lumber can be used for bunk boards along with bunk carpet like the #CE11349. However, it is possible that some corrosion may occur from the chemicals in the lumber over time. The CE Smith bunk boards like #CE27840 are made from…

view full answer...

Answer 5

The CE Smith Bolster Bracket for Pontoon Boat Trailers part #CE10052-32G does not have a specific pontoon tube size requirement. That said, the CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers part #CE26244G would likely be a better option…

view full answer...

Answer 6

Yes, you could use 2 inch by 4 inch bunks on the CE Smith Bolster Bracket #CE10052-32G.

view full answer...

Answer 7

The CE Smith Bolster Bracket #CE10052-32G that you referenced is designed for supporting a pontoon boat when on a trailer so it could work for your pontoon lift. I spoke to my contact at CE Smith about the weight capacity of the bracket and she said…

view full answer...

Answer 8

You probably could make 2x4 bunks work on the CE Smith V-Wing Bolster Bracket #CE26244G but ideally you are going to want to use the taller boards like a 2x6 or 2x8.

view full answer...

Answer 9

I recommend the V-Wing Bolster Bracket for Pontoon Boat Trailers #CE26265G40. They are galvanized and allow for 4" wide bunk boards. These are sold individually so be sure to order enough for your application. I also recommend the Bunk Style…

view full answer...

Answer 10

The CE Smith V-Wing Bolster Bracket #CE26244G that you referenced 15-1/2" long x 3" wide x 6" tall with mounting slot dimensions of 7-1/2" long x 1/2" wide. If you need further dimensions feel free to email me back with what…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Why Does the CE Smith Bolster Bracket for Pontoon Boat Trailers Not Have A Weight Capacity

Product Page this Question was Asked From

Continue Researching