Replacement Threaded Hitch Pin for Older Yakima BigHorn Bike Rack for 1-1/4 Inch Trailer Hitches

Question

Question:

I have an older Yakima BigHorn 4 with a 1-1/4 shaft first generation. will this pin work on it? The specs of this product list the bighorn but i wanted to double check. thank you in advance

asked by: Hani S

0

Expert Reply:

Replacement Hitch Bolt and Clip # Y8890200 is for racks that fit 2 inch hitches. Since your older BigHorn fits 1-1/4 inch hitches, this is not the correct pin. For the 1-1/4 inch BigHorn bike racks you can use replacement pin, clip, and lock washer # Y8880129.

expert reply by: Michael H

0

Answer 1

The Replacement Mounting Hardware for Yakima HoldUp Hitch Mounted Bike Carrier - 1-1/4" Hitches #Y8880129 is a 1/2 inch diameter with a thread pitch of 13 (threads per inch). It is 4.28 inches long. I contacted the manufacturer to get their…

view full answer...

Answer 2

The diameter of the pin on the Trailer Hitch Receiver Lock #e98879 is 1/2 inch. I spoke with my contact at Yakima to learn more about your bike rack. The rack you have is a ROC 1.25. This bike rack is designed to use a threaded hitch bold. For a…

view full answer...

Answer 3

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 4

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 5

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Replacement Threaded Hitch Pin for Older Yakima BigHorn Bike Rack for 1-1/4 Inch Trailer Hitches

Products Referenced in This Question

Continue Researching