What Are The Measurements Of The Yakima Hitch Pin #Y8880129?

Question

Question:

Ive got a 4-bike fold-down Yakima hitch rack probably made sometime around 2000-2003, for a 1-1/4inch receiver. I cant find any sort of model number on it. I want to make sure this matches the rack, and cant find diameter listed. Thanks

asked by: Jase

0

Expert Reply:

The Replacement Mounting Hardware for Yakima HoldUp Hitch Mounted Bike Carrier - 1-1/4" Hitches # Y8880129 is a 1/2 inch diameter with a thread pitch of 13 (threads per inch). It is 4.28 inches long. I contacted the manufacturer to get their official measurements for this part.

expert reply by: Jason S

0

Answer 1

Bike carriers that are designed to work on the rear of an RV are made so that they can take the additional stress at the back of the RV. Yakima does not recommend using the HoldUp Rack on RVs because a bike rack mounted on the rear of a motor home…

view full answer...

Answer 2

I went out to the warehouse and measured one of the Yakima LongHauls, part #Y02476, and it uses a 5/8 diameter hitch pin.

view full answer...

Answer 3

If the Yakima RidgeBack Bike Rack was just purchased then most likely the wedge is not tightened correctly and you just need to redo that portion of the install process. However, if this is an older bike rack then most likely the cause of this is…

view full answer...

Answer 4

Comparing Yakima Hitch Pins for 1-1/4 inch receivers #Y8880129 and #Y8890176, they looked identical to me, so I contacted Yakima and they are in fact identical parts. They just give different numbers to them for some reason, but the diameter, pitch,…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Hey Dave, so the best option for carrying your carbon frame bike and e-bike is the Swagman Escapee part #S39SR with the ramp #S59SR . It has the capacity for carrying an e-bike, is rated for travel trailer use, only touches the bikes by the tires…

view full answer...

Answer 11

As long as the flat tow wiring is wired in before the 4-Way #C93ZV and you connect the power for the converter directly to the battery it will work. I have seen several use Magnetic Lights #TL21RK which they will wire in on the main harness to have…

view full answer...

Answer 12

Hey Buddy, so the Fastway Adjustable Ball Mount part #DTSTBM6825-2S is a really great choice for the 2-1/2 inch hitch of your 2021 Ford F-250 which is going to be very solid in your hitch due to it's built in anti-rattle device that is easy to…

view full answer...

What Are The Measurements Of The Yakima Hitch Pin #Y8880129?

Product Page this Question was Asked From

Continue Researching