Why Won't My 1-1/4 inch Ball Mount Slide Into a Class I Hitch
Question:
The draw bar I have to fit into my hitch will not go back far enough to line the holes up where the pin goes threw. There is a screw inside the hitch on the right side behind the hole and it does not allow the draw bar to go back far enough. Any suggestions on how to get this to work?
asked by: Sam A
Expert Reply:
It sounds like you have a Class I hitch and are trying to use a Class II drawbar with it. Class I hitches are designed to do exactly what you are trying to do, prevent the use of a Class II accessory by not letting the holes line up. This is to prevent overloading the hitch. I attached an FAQ on hitch classifications for you to check out also.
The correct ball mount to use with your Draw Tite Hitch part # 24915 would be the Sportframe Draw Bar part # 3593.
Products Referenced in This Question
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories - 61" x 1" - Qty 1
- Q&A: What is the Difference Between Class 1 and Class 2 Hitches for the Scion XB
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Review of Curt Custom Fit Vehicle Wiring - Trailer Hitch Wiring - C56404
- Article: My Trailer Hitch Doesn't Fit
- Q&A: My 2 Inch Hitch Adapter Will Not Fit My 1-1/4 Inch Hitch Receiver on 2005 Ford Focus
- Q&A: What Size Bolts Are Used to Install 2 Inch Hitch Receiver to 2022 Subaru Forester
- Shop: Replacement Hardware Kit for Trailer Hitches
- Shop: Draw-Tite Trailer Hitch Conical Tooth Washers - 3/8" Diameter - Qty 1
- Shop: Replacement Hardware Kit for EcoHitch Trailer Hitch
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Search Results: installation hitch hardware kit
- Video: Trailer Hitch Installation - 2014 Audi Q5 - Curt
- Q&A: Will the Backup Sensors on my 2019 Tesla Model 3 Activate Carrying Thule T2 Bike Rack
- Q&A: Recommended Trailer Hitch for 2017 Dodge Journey Crossroad
- Q&A: Does Draw Tite Hitch # 75648 Allow Rear Spare to be Left Installed on 2017 Dodge Journey
- Search Results: draw~tite
- Search Results: saris freedom 4
- Video: Saris Freedom Hitch Bike Racks Review - 2014 Dodge Journey
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Choosing the Right Trailer Wiring
- Search Results: hitch
- Article: How to Choose the Right Trailer Hitch Class
- Video: Choosing the Right Brake Controller
- Shop: Roof Rack