Screw Size Included with the Tekonsha Replacement Mounting Bracket # 2178

Question

Question:

What size are the screws to hold brake into the bracket, I lost mine. Thank you.

asked by: Jay

1

Helpful Expert Reply:

The screws are pretty small, I went out into our warehouse and pulled the Tekonsha Replacement Mounting Bracket # 2178 to measure the screws for you and found them to be 1/2 inch long, 1/8 inch in diameter and would use a 1/4 inch wrench or socket to tighten.

expert reply by: Jameson C

1

Answer 1

I have attached a photo for you below which shows how both a vehicle side and trailer side trailer connector is typically wired. I say typically because this is not always exact and so long as the trailer and vehicle side both match it will not…

view full answer...

Answer 2

Are you replacing the races in the hub? I ask because the hubs and hub and drum assemblies we sell come with the races already installed so you would not have to reuse the old ones. Races are difficult to remove but since you have one out already you…

view full answer...

Answer 3

The bearing races on a trailer hub, like the Trailer Hub Assembly, part #8-258-5UC1, are removable, they are not built into the hub. I am including a link to a FAQ page on wheel bearings, races, and seals. Also, a link to a video of removing and…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Screw Size Included with the Tekonsha Replacement Mounting Bracket # 2178

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching