Location Of Under Dash Brake Controller Port On 2002 Ford F150

Question

Question:

Theres a grey port next to the diagnostic system. Is that the port that operates the brake controller? It has five pins in it, though.

asked by: Danny B

0

Expert Reply:

You are right that the gray port is right next to the diagnostic port under the dash on your 2002 Ford F-150 for the brake controller. I have attached a photo that shows where the brake controller port is in relation to the location of the diagnostic port.

I have also attached a helpful article for brake controller installation on Ford full-size pickups you can check out.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

I looked up pictures of the interior of your 2021 Toyota Tacoma and it is pretty tight but it looks like there's a cubby hole area in front of the gear shifter that you could fit the Tekonsha brake controller #TK90160. The correct install harness…

view full answer...

Answer 2

The #C57672 will allow you to convert an existing 4 pin connector on a vehicle and allow it tow a trailer that has a 7-way. By attaching the mounting bracket to the underside of the bumper or chassis of the tow vehicle, plugging the 4 pin on the…

view full answer...

Answer 3

It wouldn't be a fuse since the brake controller is getting power. If the truck is parked then there may not be any power on the blue wire when stepping on the brake pedal (depending on which controller you are using) but there should be power…

view full answer...

Answer 4

Sounds like you have a blown third brake light fuse. I bet if you grabbed the override lever of the controller it would still activate the trailer brakes. An easy way to check this is to apply the vehicle brakes and check to see if the third brake…

view full answer...

Answer 5

To install a brake controller on your 2017 Ford F750 you will need to hardwire it as there are no factory plugs under the dash. There will be some wires located under your dash that are located on the driver side. You will simply need to use a…

view full answer...

Answer 6

If the tongue weight of your setup is 708 lbs when the trailer is fully loaded then the Fastway e2 Weight Distribution w/ 2-Point Sway Control part #FA94-00-1061 is a great choice. The Fastway e2 is designed for tongue weights between 600 lbs - 1,000…

view full answer...

Answer 7

The connector for installing your brake controller is located under the dash. Directly under the steering column, you will see the diagnostic port. The port for the controller is located above and behind, as you can see in the photo I've…

view full answer...

Answer 8

The flashing output of a Curt Triflex normally indicates that the brake pedal is pressed but a trailer isn't connected. Since yours is flasing all the time that would indicate that you most likely have a short between the 12 volt power wire for…

view full answer...

Answer 9

I took a look at the owner's manual for the 2001 Ford F-150 5.4L 4WD Super Crew and the maximum trailer weight that can be towed with this vehicle is 8,300 lbs with or without a weight distribution hitch if you have an automatic transmission. It…

view full answer...

Answer 10

The correct brake controller wiring adapter for your 2009 Ford Explorer Sport Trac and the Curt Venturer Brake Controller, #C74VV, is the Curt Custom Wiring Adapter, #C51322. On the Sport Trac, the factory brake controller plug is behind the dash…

view full answer...

Answer 11

To install the Curt TriFlex #C24VV trailer brake controller in your 2006 GMC Savana Van you will need to wire in harness part #C51515. Vehicles with the 7-way tow package have the blue output brake wire already run from the back to the front. It is…

view full answer...

Answer 12

Unless you plan on adding over 150 lbs in the bed of your 2015 Ford F-250 Super Duty I recommend going with the Fastway e2 #FA92-00-0600 as the Tongue Weight (TW) capacity of 600 lbs is a good spot to be at. Even though the e2 #FA92-00-0800 system…

view full answer...