Total Height of Spring, Bracket and Spacer on Timbren Rear Axle Spring Kit # TFR250SDE

Question

Question:

Can you tell me the total height of the spring, bracket and spacer. I would like to take a measurement of my truck before placing my order. Thanks

asked by: Mark

0

Expert Reply:

The Timbren rear axle jounce spring kit for Ford trucks that you referenced, part # TFR250SDE, is a correct fit for the 2002 F-250 Super Duty. This kit will fit both 2-wheel-drive and 4-wheel-drive versions and installs without drilling.

The attach photo shows the dimensions of each of the main components in this kit. The springs are 5-1/16-inch tall, the spacer is 1/2-inch thick x 3-7/8-inch diameter, and the overall height of the bracket is 2-inches.

I have linked both the written installation instructions and a video showing this kit being installed in your same year/make/model truck.

expert reply by: Adam R

0

click to enlarge

Answer 1

I have attached a photo of the #RP50082-58 bracket installed on a truck like yours. As you can see, there is no interference with the bump stop you have installed on the truck. I recommend the Timbren Rear Suspension Enhancement System, part…

view full answer...

Answer 2

Yes, the Timbren kit part #TFR250SDE that you referenced is a confirmed fit for your 2004 Ford F-250 2wd with stock height suspension. I attached an install video we made that shows this kit installed on a 2004 F-250 just like yours for you to check…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 9

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 10

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Answer 11

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 12

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Total Height of Spring, Bracket and Spacer on Timbren Rear Axle Spring Kit # TFR250SDE

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching