Which Timbren Kit Fits 2004 Ford F-250 2WD with Stock Suspension

Question

Question:

Will these work on my 2wd stock suspension and stock height

asked by: Matt

0

Expert Reply:

Yes, the Timbren kit part # TFR250SDE that you referenced is a confirmed fit for your 2004 Ford F-250 2wd with stock height suspension. I attached an install video we made that shows this kit installed on a 2004 F-250 just like yours for you to check out as well.

expert reply by: Jameson C

0

Answer 1

You have many options for a 4 inch lift on your 2001 Ford F-250 4x4 regarding suspension enhancement to reduce sag. For an air spring option, I recommend the Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle #AL57390 along with the Air Lift…

view full answer...

Answer 2

It is permissible to stack two 1-inch spacers #A25723-90AH00 to give you a total of 2-inches of height adjustment for your Timbren rear axle kit. Rear axle jounce spring kits like those from Timbren are intended primarily for use with supporting…

view full answer...

Answer 3

Since you have a 6 inch suspension lift on your 2015 Ford F-150 a trailer what you will need to use is the Timbren Rear Suspension Enhancement System #TFR1504E. The reason for that is the SumoSprings do not have lift spacers available to make up for…

view full answer...

Answer 4

The Timbren Rear Suspension Enhancement System part #TGMRTT15S for the 2000 GMC Sierra 1500 springs themselves measures 3-1/4" tall. If you use the spacer the spring will be 4-1/4". Timbren does require 1/2" and 1-1/2" between the…

view full answer...

Answer 5

When installing suspension enhancement on your 2019 Toyota Tundra that a 6 inch lift The RoadActive Suspension #RAS4611TD will work for you as long as the leaf springs are stock, if not The Timbren Rear Suspension Enhancement System #TTORTUN4 will…

view full answer...

Answer 6

To be able to tow a dump trailer at your 2016 Ford F-350's maximum towing capacity of 14,000 pounds, you will need to use a weight distribution system. In Ford's towing guide, they state that the maximum loaded trailer weight requires use of…

view full answer...

Answer 7

In order to choose the best weight distribution hitch, you will first need to know your total tongue weight (TW), which is the tongue weight of your fully loaded and ready to go trailer plus the weight of any cargo behind the rear axle of your tow…

view full answer...

Answer 8

The mounting holes on the Curt SecureLatch Pintle Hook #CU97FR are spaced 1-3/4" apart vertically and 3-3/8" horizontally on center. I have an alternate solution with the information you requested as when I spoke to Curt they said this…

view full answer...

Answer 9

I have attached a photo of the #RP50082-58 bracket installed on a truck like yours. As you can see, there is no interference with the bump stop you have installed on the truck. I recommend the Timbren Rear Suspension Enhancement System, part…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...