Channel Bracket and Mounting Hardware Recommendation for the Demco 2-Tang Clevis # DM05593-97

Question

Question:

Does etrailer.com carry the channel bracket and mounting hardware for a 2inch receiver for this clevis hitch?

asked by: Brent

0

Expert Reply:

For a channel bracket to go along with the Demco 2-Tang Clevis # DM05593-97 that you referenced you would want the Demco 6-Hole Adjustable Channel Bracket # DM59601. This bracket gets welded on, for the hardware to secure the # DM05593-97 to the # DM59601 you would want the Pro Series Mounting Bolts for Adjustable-Channel Couplers # PS024202.

expert reply by: Jameson C

0

Answer 1

Channel Tongue Trailer Coupler #CT-3001-Z requires a 2 inch wide tongue but I recommend a boxed tongue and not C-channel so there is more support where it counts. Steel tubing at least 1/8 of an inch of wall thickness will do the trick. The length…

view full answer...

Answer 2

The depth of the channel of the Demco 6-Hole Adjustable Channel Bracket #DM66134 is 2-1/8 inches. This is a standard depth for this type of channel.

view full answer...

Answer 3

I was able to get a dimensional drawing from Buyers Products which I have attached below. The Buyers Products Coupler w/ 5-Position Adjustable Channel - Weld-On - 2" Ball - 10,000 lbs #3370091545 has 6 mounting holes on each side, providing 5…

view full answer...

Answer 4

Adjustable trailer couplers are not going to mount to your truck; they will attach to the frame of your trailer. Some of the adjustable couplers, such as the Bulldog Cast Head #BDA2563C0317 come with the mounting hardware to weld onto the frame of…

view full answer...

Answer 5

The Demco 6-Hole Adjustable Channel Bracket #DM66134 is pretty thick. The steel thickness used for this is 7/16 of an inch.

view full answer...

Answer 6

I have a solution for you, but Titan does not offer their Bolt-On Coupler for 2-5/16 Inch Ball #T4855300 in a 2 inch hitch ball design. For a bolt-on trailer coupler with a trigger latch, designed for a 2 inch ball I recommend the Demco Trailer…

view full answer...

Answer 7

The inside mounting channel width is just under 2 inches, while the outside width (as you mentioned), is just under 3 inches, designed to fit into a 3 inch wide channel, like #BDAC5000300. The overall length is 10 inches, as shown in the attached…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Channel Bracket and Mounting Hardware Recommendation for the Demco 2-Tang Clevis # DM05593-97

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching