Replacement Landing Gear Motor for a ADTH E226168

Question

Question:

My 2005 Ragen 30foot toy hauler has a ADTH E226168 motor do you have a replacement motor thanks.

asked by: Mike D

0

ADTH E226168
(click to enlarge)

Expert Reply:

Thanks for the picture! We sure do! You will want the Replacement Motor for Stromberg Carlson Electric Landing Gear item # LG-142178.

expert reply by: Jerred H

0

Answer 1

From what I could find it looks like your ADTH 1RV-200 motor has a weight capacity of 6,500 lbs. You can use a motor that is rated for a higher capacity, like our replacement motor #LC142178 for Ram landing gear which is rated at 8,000 lbs. Just…

view full answer...

Answer 2

First thing I'd check is the power source and ground for the landing gear. What you described could be a bad motor, but a weak battery or ground will cause the same problem. Your picture is pretty close up, but it looks like the motor…

view full answer...

Answer 3

In case you want to just service your existing Venture VMC940 5th wheel landing gear driver leg you can use gearbox #LG-179015. For a complete replacement lead jack use Replacement Lead Jack with Drop Leg #LG-179013 which is a universal fit that…

view full answer...

Answer 4

The correct replacement gear box for your Venture landing gear VMC940RB is part #LC276602. This features cast aluminum construction that will last longer than a composite gearbox like #RVLG-RDBOX which fits Ram brand landing gear model #RVLG-8000.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The stop light switch that you will need to connect the red wire to on the Brake Control Plug-In Harness for Tekonsha part #20127 may be pre ran to a set of wires taped to the underside of the drivers side vehicle dash. If the wires are not present…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

It could be the motor but it could also be the screw/nut inside the jack leg that is causing the problem. Since you mentioned that it is hard to crank it manually I suspect that it is likely the screw and/or nut. On jacks that have an ACME screw…

view full answer...

Answer 10

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice.…

view full answer...

Answer 11

Yes, the Replacement Motor for Stromberg Carlson Electric Landing Gear #LG-142178 has been confirmed to replace the ADTH 1RV-200 landing gear motor you currently have so it would work for you.

view full answer...

Answer 12

The Replacement Motor for Stromberg Carlson Electric Landing Gear - 5,500 lbs #LG-142178 is the correct replacement motor for the discontinued Atwood 75721. The #LC141893 you asked about will also work and is a higher speed motor so it will give…

view full answer...

Replacement Landing Gear Motor for a ADTH E226168

Product Page this Question was Asked From

Continue Researching