Picking Out Center Cap for Wheel of 2023 Keystone Cougar 25RDS

Question

Question:

Im looking for a trailer wheel center cap plug for my 2023 Keystone Cougar 25RDS. Can you help me find the correct one?

asked by: Gary L

0

Expert Reply:

Hey Gary, so to pick out a wheel center cap we need to know the diameter of your wheel's pilot hole (center hole). With that we'd be able to figure out what you need. For example, the part # 319EZ is correct fit if the diameter is 3.19 inches.

I attached a link to all of the wheel center caps we offer as well if that's not correct size.

expert reply by: Jameson C

0

Answer 1

Unfortunately we do not have a way to replace the keys without knowing the key number for the lock. If they happened to have written down the key number from the lock then we will be able to get you a replacement. The etrailer Trailer Hitch…

view full answer...

Answer 2

Base plate kits are somewhat time consuming but they aren't too terribly long. I once asked our install guy that's been here forever how long to set aside for a base plate kit install and he said a "long afternoon"…

view full answer...

Answer 3

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still…

view full answer...

Answer 4

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and…

view full answer...

Answer 5

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 6

According to my research, your 92865A-1 hub/drum has a 25580 inner and an 14125A outer bearing and a 8 on 6-1/2 inch lug pattern, as does the AxleTek #AKHD-865-7-2-K hub drum you referenced. The #AKHD-865-7-2-K would be an acceptable replacement for…

view full answer...

Answer 7

Dexter Nev-R-Lube Bearings such as the 50MM #31-71-3 referenced in your question do not have a specific maintenance or replacement schedule. These are pre-lubricated at the factory, which will make it resistant to contamination, and sealed for life…

view full answer...

Answer 8

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 9

I recommend to use the Solera 16-1/2' Slider part #LCV000435661 which matches the boxes width exactly so you will not have side overhang like we normally recommend but it is the biggest slide topper available to fit the 198" width of your…

view full answer...

Answer 10

We have toppers that'll work for 2 of your 3 sliders. For your 12 foot 9-1/2 slide, use #LCV000168109 which is designed for slides measuring between 152-157 inches wide. The longest topper we offer is for slides 188-193-3/4 inches, so…

view full answer...

Answer 11

Please note the attached instructions. The Lippert Anti-Billowing Kit for Solera Slide Topper Awnings, #LC78FR should be installed on the end of the awning that is closest to the front of the unit. 1. Make sure awning is fully retracted. 2. Place the…

view full answer...

Answer 12

I advise measuring the two spindles that you have and making sure that the parts that you are wanting to interchange will be a compatible fit. I have included a photo that shows where where to take these measurements on your exiting spindles. These…

view full answer...

Picking Out Center Cap for Wheel of 2023 Keystone Cougar 25RDS

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching