Solution for Needing Replacement Light Switch for Lippert Electric Trailer Jack

Question

Question:

Hello, I am looking for the Lippert Tongue Jack replacement on/off switch for the light. What part number is that?

asked by: Amie T

0

Expert Reply:

Hey Amie, for the Lippert electric trailer jack part # LC285318 if you need replacement switches you'll need the replacement top cover # LC285160 as just the light switch is not available.

expert reply by: Jameson C

0

Answer 1

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 2

Lippert does not offer a replacement inner jack tube for their jack 1817941. When a jack is damaged in this way (which is more common than you want to know) it really is best to replace the entire jack for safety reasons. The outer tube on your jack…

view full answer...

Answer 3

Hi Robert, So there isn't one that can be used with a cordless drill (which would be an electric jack only) as all the electric A-frame jacks are all higher than the 12" to 14" you want. There is a manual crank jack you can use which I…

view full answer...

Answer 4

Hi Robert, So I know you don't want to, but the only option for a hitch extension for your 2-1/2 inch hitch does reduce the receiver to 2 inches. I hope you're not mad at me, but there unfortunately is no 2-1/2 inch hitch extender that also…

view full answer...

Answer 5

Because of its functionality with the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System #LC672136 you do need to replace the 421366 tongue jack with another one. The correct part is the following: - Replacement Tongue Jack…

view full answer...

Answer 6

It will indeed work; I just checked with Lippert for you and was able to verify the correct toggle switch for your Lippert Power Stance Electric Trailer Jack #LC69VR (which is the 813748), is the following: - Replacement Extend/Retract Switch for…

view full answer...

Answer 7

The correct replacement for an Atwood Water Heater GC6AA-9E is the Dometic RV Water Heater part #DMC74FR. This is a 6 gallon water heater that works with both gas and electric just like the one you have so it will be an exact match.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

To keep your back end from squatting, I recommend the Coil SumoSprings Custom Helper Springs for Coil Spring Suspension item #CSS-1094R. These insert into your rear springs and keep your suspension from being pushed down by the weight of your…

view full answer...

Answer 12

Congrats on the new camper! I have a solution but there unfortunately is not a manual to electric conversion kit for the HappiJac 4160 series jacks. The reason an electric conversion will not work for your 4160 is that they have a two piece…

view full answer...