Recommended Seal and Bearing Kit for a Dexter D60 Axle

Question

Question:

Looking for a Dexter D60 ez lube seal and bearing kit to keep on board as a spare. Axle sticker below.

asked by: Michael R

0

Expert Reply:

I didn't receive a picture which you can email to me directly if you would like. However, since you have a Dexter D60 axle you will need the Bearing Kit, 14125A/ 25580 Bearings, 10-36 Seal item # BK3-200 you were looking at.

expert reply by: Jerred H

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

I was able to cross reference the Dexter part number 031-17-02 to a #14125A bearing and part 031-030-02 to a #25580 bearing, and we do have these replacement parts with a grease seal in a complete kit for you. For a replacement bearing/race/seal kit,…

view full answer...

Answer 3

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 4

You can use the other components you remove from your hubs. After you have removed the hub components you will want to inspect all of the parts and replace if you find any discoloration or signs of wear or damage such as a nick. On the race you can…

view full answer...

Answer 5

Thanks for the axle information, Mike! Here are the correct parts according to my contact at Curt: - Bearing #02475 and Race #02420 - Bearing #25580 and Race #25520 - Grease Seals #RG06-070

view full answer...

Answer 6

The correct bearing kit for your 7,000 pound Lippert axle is #BK3-210.

view full answer...

Answer 7

I was unable to identify your exact axle but I found Trailer Hub and Drum Assembly #AKHD-865-7-2-EZ-K to work if you have EZ Lube axles. If you do not have EZ Lube axles use Trailer Hub and Drum Assembly #AKHD-865-7-2-K. Both of these kits will come…

view full answer...

Answer 8

Yes, the bearing kit part #BK3-210 does fit a good portion of the 7,000 lb Dexter axles out there, but some of the 7k Dexter axles require a slightly larger grease seal which instead requires the kit part #BK3-200. What you'll want to do is…

view full answer...

Answer 9

Hey David, thanks for the picture. I was able to track down a spec sheet for your Dexter axle which I have included below. The 031-029-02 bearing is item #15123 and the 031-030-02 bearing is item #25580. For a bearing kit you can use part #BK3-110…

view full answer...

Answer 10

The side plates of the B&W gooseneck trailer hitch #BWGNRK1313 will mount on the outside of each frame rail of your 2004 Dodge 2500 8-foot bed. See the B&W video I included at the 7 min and 30 second mark. If your Firestone air bags like…

view full answer...

Answer 11

I have a solution that may work for you, but we do not currently have any 3" diameter submersible reverse lights. Have a look at the Optronics Backup Light #BU45CB which is a 4-1/4" diameter light that can be mounted to your trailer using…

view full answer...

Recommended Seal and Bearing Kit for a Dexter D60 Axle

Product Page this Question was Asked From

Continue Researching