Correct Wedge for a Lippert Turning Point Pin Box and a Reese Pro Series 15K Hitch

Question

Question:

Looking for the correct wedge for a Reese Pro Series 30093 Fifth Whgel hitch? Can you provide the correct wedge to use with the Turning Point product? Thank you.

asked by: Mark

0

Expert Reply:

The Lippert Turning point pin box uses a universal wedge that's compatible with all 5th wheel hitches, so you'd just need the Replacement Wedge Block for Lippert Turning Point Pin Box # LC79UD.

expert reply by: Bryce D

0

Answer 1

It could be that, or you could be using the wrong wedge. If you have the A20 then you should be using the Sidewinder Wedge for Curt A Series 5th Wheel Trailer Hitches #C16992. If you're not try and swap them out and see if that fixes your issue.…

view full answer...

Answer 2

I checked the Lippert Turning Point manual and below attached the maintenance recommendations. No mention of needing to lube the hitch plate is listed so you really don't need to lube that area. If you insisted on doing so a graphite lube like…

view full answer...

Answer 3

The 6169 number you provided comes back to the Replacement Head for Demco Recon #DM6169. With the picture you provided, it looks like you have the Demco Recon 5th Wheel Trailer Hitch #DM8550043. The wedge that you would need to use with your Lippert…

view full answer...

Answer 4

We have had really good reports of the Reese Sidewinder wedge fitting with the Lippert Turning Point (see attached photo of review) and so for your Husky 16K 5th wheel hitch the wedge you'd want is part #SWW-04. This will fit more snug in the…

view full answer...

Answer 5

The universal wedge that came with the Lippert Turning Point King Pin should work just fine with your B&W Companion OEM 5th-Wheel Hitch #BWRVK3300. I do recommend considering a custom wedge instead that is specifically designed for your B&W…

view full answer...

Answer 6

Since the wedge you have worked correctly the first time you connected your Lippert Turning Point Pin Box to your B&W Patriot 5th wheel hitch #BWRVK3200 then I would indeed go ahead and loosen/uninstall the wedge and reinstall it. You said you…

view full answer...

Answer 7

The "Trailer Disconnected" error message on the dash with a factory brake controller is usually related to an issue with the blue brake output wire that runs from the brake controller to the 7-Way connector. The fact that the issue remains…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...