Rhino-Rack Aero Bar Roof Rack for Camper Shells # Y03-320 Total Height

Question

Question:

How tall are the feet from the rail to top of the crossbars I have Thule rails on a ARE truck cap

asked by: Jim B

0

Expert Reply:

Hi Jim,

The Rhino-Rack Aero Bar Roof Rack for Camper Shells # Y03-320 are going to sit approximately 4" tall from the top of your A.R.E. truck cap.

expert reply by: Kevin C

0

Y03-320 height
(click to enlarge)

Answer 1

I have a solution for you, but the Rhino-Rack Roof Rack for Thule and Yakima Tracks - 2 Heavy-Duty Crossbars - Black - 65" Long #Y01-140B-NT is made to attach to pre-installed tracks and you would need to drill into your roof in order to…

view full answer...

Answer 2

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

Hey Alec, For your 2016 Ford Fusion I recommend the recommend a roof rack from Inno: Inno Aero Crossbars #INXB138-145 Inno Through Feet for Aero Crossbars #INXS250 Custom Fit Kit for Inno XS200, XS250, and INSU-K5 Roof Rack Feet #INK860 As with any…

view full answer...

Answer 6

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your canopy. Per…

view full answer...

Answer 7

With the size of your Champion Generator 200953(23.4" wide, 27.9" long and 21.7" tall I recommend using the 32x48 Reese Solo Cargo Carrier #PS1040100. This has a 47-3/4" long by 31-3/4" wide inner tray and can support up to…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 11

For frame mounted camper tie downs that are a confirmed fit for your 2016 Dodge Ram 3500 Dually we have the TorkLift camper tie downs part numbers #TLD2131 for the front and part #TLD3109 for the rear.

view full answer...