Which Hitch for 2021 Toyota Highlander Allows Full Sized Spare to Be Stored

Question

Question:

Which trailer hitch model will allow a full sized spare to remain installed on a 2021 Toyota Highlander? Thank you, John

asked by: John M

0

Expert Reply:

For your 2021 Toyota Highlander the trailer hitch we offer that allows the largest spare to be stored under it is the Draw Tite part # DT84MR which can fit an 18 inch or 20 inch spare as long as it's a steel wheel.

expert reply by: Jameson C

0

Answer 1

It is a 3-way switch. The SeeLeveL RV Holding Tank Monitoring System, #SE39VR includes a panel that incorporates readings for sensors to track 3 holding tanks, display of battery voltage and includes water pump switch. The integrated switch activates…

view full answer...

Answer 2

We don't currently carry replacement pressure switches for any of the water pumps that we carry so you would need to reach out to HydroMax directly to get a replacement pressure switch for your HydroMax RV Fresh Water Pump #P25201 or will need to…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Which Hitch for 2021 Toyota Highlander Allows Full Sized Spare to Be Stored

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching