When To Replace Your Brake And Hub/Drum Assemblies And How To Handle Discoloration On The Spindle
Question:
What does UC3 mean? I bought 2 drums before 2020 and there was not UC3 at the end of the numbers. Are those genuine Dexter parts?. I have a little over 1/16 left on one pad I would think, can you look at the photo and give me your opinion? If I change the back plate, is it best I change the drums too? have them turned? Also the Dexter manual mentions to check for discolouration on the spindle, I have some collars on the spindle, could you check the photos if that is ok? Thank you very, Julie
asked by: Julie P
Expert Reply:
Hi Julie,
UC3 is added on to this part number because we offer parts with the same part numbers from multiple manufacturers so a code or extra numbers get added on to differentiate the parts. If you scroll down on the # 8-388-80UC3 page you'll see the manufacturer's part number (pictured below) after the item description.
Dexter recommends replacing the brake assembly when the pads get down to 1/16" (.0625") in order to prevent damage to the hub or failure of the brake assembly. They recommend replacing the hub/drums every time you replace the brakes because they build a groove and form to each other over time. They follow very strict guidelines to make sure that everything is perfect each time. Most people however, just check the drum for any deep scratches or gouges and replace as necessary. If you can get them turned for a reasonable cost then that's the route I'd take.
When it comes to light duty (axles under 8k) brake assemblies it's typically cheaper and easier to just replace the entire assembly rather than replacing the shoes. Replacing the assembly will also give you a new warranty in the event that anything malfunctioned. If you do want to replace the shoes you still can but you'll likely have a hard time because the shoes are held in place with tight springs that don't want to cooperate.
The discoloration on the spindle is concerning because it's right where your grease seal sits. If the grease seal fails it will allow water, dirt, debris, etc. into the hub and can bind up or corrode the bearings. If your bearings bind up the wheel won't want to spin and it'll heat up and destroy the spindle. You can try lightly sanding the rust with some very fine sandpaper to remove some if it but you don't want to sand too much and build a groove in the spindle. You're likely looking at needing a new axle in the near future, but could probably ride this one out just a bit longer.
When you do end up having to replace the axle you'll need to know the capacity, hub face to hub face measurement, and spring seat to seat seat measurement.
Product Page this Question was Asked From
Trailer Hub & Drum Assembly - 6,000 lbs Axles - 6 on 5-1/2 - Nev-R-Lube
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Nev-R-Lube
- For 6000 lbs Axles
- 6 on 5-1/2 Inch
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- Dexter
more information >
Continue Researching
- Shop: Americana Metal, Bolt-In Valve Stem - 1-1/4" Long
- Shop: Trailer Hub & Drum Assembly - 6,000 lbs Axles - 6 on 5-1/2 - Nev-R-Lube
- Search Results: 303
- Shop: Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs
- Shop: Dexter Nev-R-Adjust Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 7K
- Search Results: 008~388~80
- Search Results: 23~458~459
- Search Results: dexter drums
- Search Results: 23~458
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Hitch
- Search Results: lug nuts
- Shop: Dexter Trailer Hub and Drum Assembly - 7K lb E-Z Lube Axle - 12" - 8 on 6-1/2 - 1/2" Studs
- Article: Most Popular Wheel Bearings
- Q&A: Does 15" Americana Aluminum Mod Trailer Wheel Have a Max PSI Rating
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Trailer Wiring
- Search Results: lug nut
- Video: Americana Metal Bolt-In Valve Stem Review
- Q&A: Metal Valve Stems that Fit 2023 Grand Design 2910BH
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Video: Americana Tire Inflation and Repair - Valve Stems - AM20906 Review
- Article: Trailer Tire Sizing
- Shop: Brake Controller
- Shop: Gooseneck Hitch
- Q&A: What Is The Offset For The Aluminum HWT Hi-Spec Series 03 Mod Trailer Wheel # AM22327
- Video: Americana Tire Inflation and Repair - Valve Stems - AM20907 Review
- Article: Trailer Wiring Diagrams
- Shop: Suspension Enhancement
- Video: Hopkins Wiring - Tools for Wiring - HM50918 Review
Julie P.
3/20/2024
Thank You for your Prompt response, I have Nev-R-Lube bearings, maybe it is more protected from debris. I noticed those marks on the spindle 4 yrs ago, I did not know then it could be an issue. Nothing seems to have gotten worse but I will litly sand and keep a close eye on the spindles and a possible Axle replacement.