Is Regal Style Back Cover for Solera Power Awnings Hard to Install

Question

Question:

How hard to replace the Back Cover for Solera Power Awnings - Idler Head - Regal Style

asked by: Jim S

0

Expert Reply:

Hey Jim!

The Replacement Back Cover for Solera Power Awnings - Drive Head or Idler Head - Regal Style - Black # LC643921 is a pretty simple installation that just requires you to remove the mounting screws, remove the cover, and then reverse the order for the new cover.

This does install with 6 of the Head Cover Fastener # LC266156 so if your mounting hardware needs to be replaced then you'll want to pick these up as well.

expert reply by: Jon G

0

Debi

3/22/2024

whatz the length of this screw ?? LC266156

Reply

Jon G.

3/28/2024

@Debi The Replacement Head Cover Fastener # LC266156 is 1/2" long and has a 1/8" diameter.

Reply

Answer 1

Thanks for the information. I checked with Lippert and didn't get anything back on the first two numbers and the last one is a fire safety code. The good thing is there aren't many options for replacement motor covers for Solera…

view full answer...

Answer 2

To replace the screws on the Front Cover for Solera Power RV Awnings item #LC643922 you will want the Replacement Solera Manual Awning Head Cover Fastener item #LC266156. These are #6 pan head screws that are a 1/2" in diameter. We do not…

view full answer...

Answer 3

To replace the motor on the LCI Pump 650057 we have the Replacement Motor #LC167576.

view full answer...

Answer 4

Thanks for the photo and it does show the left side, which is the idler head side. I can verify for you that the you do have the correct replacement cover: - Replacement Cover for Solera Awnings - Idler Head - Front Cover - Black #LC643923 This…

view full answer...

Answer 5

To remove the front cover #LC643923 from your Solera Awning there are indeed 2 screws that need to be removed. If you look at the back f the idler head unit you can see the locations where the screws reside that you need to remove. I have attached…

view full answer...

Answer 6

Since you have a regal-style Solera awning the correct front cover for the drive head would be part #LC643922. If you needed to replace the idler head as well then you'd want part #LC643923. If the back side of the cover is damaged for…

view full answer...

Answer 7

The Aluminum Liger Trailer Wheel #LH39FR has a 4.88" pilot diameter. This means the correct cap is the Lionshead Trailer Wheel Center Cap #LHCS109-SI60C.

view full answer...

Answer 8

I forwarded your photo to my Lippert representative, and found that the correct front drive head cover you'd need is Lippert part number 771407 which we carry as part #LC32NJ. Thanks for providing the photo, that make the process much easier!

view full answer...

Answer 9

Meg, for your Lippert Solera 2000 series awning you can use the Replacement Front Cover for Lippert Edge Awnings #LC32NJ for the front and #LC43UD for the rear to replace your damaged cover. Also, if by cap you're meaning the manual override…

view full answer...

Answer 10

Hey Jim! The Replacement Back Cover for Solera Power Awnings - Drive Head or Idler Head - Regal Style - Black #LC643921 is a pretty simple installation that just requires you to remove the mounting screws, remove the cover, and then reverse the order…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hi Drae, You can actually cut down one of the LED Light Kits to your 117 inch specification, but I checked with the manufacturer and the #LC674283 is too long for that. Instead, what you'll need is a different length: - LED Light Kit w/ Switch…

view full answer...