Replacement Head Covers For A Regal-Style Solera RV Awning

Question

Question:

Cover of awning motor blew off somewhere…What is the correct replacement part?

asked by: Cynthia O

0

Expert Reply:

Since you have a regal-style Solera awning the correct front cover for the drive head would be part # LC643922. If you needed to replace the idler head as well then you'd want part # LC643923. If the back side of the cover is damaged for either head you can replace it with part # LC643923.

expert reply by: Kevin C

0

Awning info
(click to enlarge)

Drive Head Of Awning
(click to enlarge)

Answer 1

Thanks for the photo and it does show the left side, which is the idler head side. I can verify for you that the you do have the correct replacement cover: - Replacement Cover for Solera Awnings - Idler Head - Front Cover - Black #LC643923 This will…

view full answer...

Answer 2

Depending on the style of your awning it could be the Regal cover #LC643922 or the standard cover #LC289560. The shapes are a bit different so you'll want to verify first before purchasing.

view full answer...

Answer 3

I spoke to my contact at Lippert and he told me the Replacement Cover for Solera Awnings - Idler Head - Front Cover - Black #LC643923 would be the correct replacement cover for your power awnings. If you need the motor side cover, that will be the…

view full answer...

Answer 4

It looks like you are needing the Solera Awning Plain Drive Head Cover, #LC289560. This cover has the cut out on the left side and plug hole like the cover in the picture that you sent. This cover will be located on the right side of the awning when…

view full answer...

Answer 5

For your Solera Awning, you can use the Replacement Cover for Solera Awnings #LC643923 for the front, and the Replacement Cover for Solera Awning #LC643921 for the back. I have included a couple of videos for you to check out as well.

view full answer...

Answer 6

To remove the front cover #LC643923 from your Solera Awning there are indeed 2 screws that need to be removed. If you look at the back f the idler head unit you can see the locations where the screws reside that you need to remove. I have attached a…

view full answer...

Answer 7

The Front #LC289560 and Back #LC289561 covers that you referenced are for the drive head for the Solera Awning Plain style. Since you are needing the idler side you need the parts #LC289566 and #LC289567 instead.

view full answer...

Answer 8

There are two different types of Solera Power Awnings. The older style which had the LCI logo on the front cover and the new regal style which does not have the LCI logo on the front cover. If the old Solera Awning Plain Drive Head Front Cover, Black…

view full answer...

Answer 9

That's actually a drive head in your picture as you can see the motor. That means the correct cover is the part #LC289560.

view full answer...

Answer 10

The Solera Awning Plain Drive Head Front Cover, Black #LC289560 and Solera Awning Plain Drive Head Back Cover, Black #LC289561 are what you need for your 2017 Forest River Vibe. If you have the manual crank style then you will use #LC351832 in place…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Head Covers For A Regal-Style Solera RV Awning

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching