Switching From Regular Demco Recon Gooseneck-to-5th Wheel Adapter to Recessed Ball Adapter

Question

Question:

I have the Demco Recon Gooseneck-to-5th Wheel Trailer Hitch Adapter - Single Jaw - 21,000 lbs and don’t want to buy a new hitch when I get a flat bed. Can I get just the adapter for the recessed gooseneck ball?

asked by: Arnie P

0

Expert Reply:

The base on the # DM8550045 is completely different from the # DM8550046 so you can't simply add on the adapter for the recessed ball. However, you can swap out the base with # DM6316 and use your existing head which will save money over replacing the entire thing.

expert reply by: Robin H

0

Arnie P.

2/27/2024

Awesome!!!!!! Thank you!!!!!!! That would actually be best option as then having both bases I’d be set no matter what. Is there a veteran discount?

Reply

Robin H.

2/27/2024

@ArnieP I wish we had one but a veteran discount is not something we offer at this time.

Reply

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 6

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

The base on the #DM8550045 is completely different from the #DM8550046 so you can't simply add on the adapter for the recessed ball. However, you can swap out the base with #DM6316 and use your existing head which will save money over replacing…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...