Recommended Optronics LED Clearance Light for a Trailer

Question

Question:

Is there an LED equivalent for Optronics MC90AS amber clearance light?

asked by: Gus

0

Expert Reply:

Hey Gus, it looks like the Optronics LED Clearance or Side Marker Light # MCL95AB is going to be the LED version of the # A91AB you're looking at. This light is a bit smaller though, measuring 3/8" shorter and 1/16" narrower, but it is 3/16" deeper.

expert reply by: Bryce D

0

Optronics LED Clearance Light Dimensions
(click to enlarge)

Answer 1

Yes, because it is a 3-wire light, you can wire the Red Identification Light Bar with White LED Utility Light #OPT88FR to function as rear marker and reverse lights.

view full answer...

Answer 2

The length is 19 inches of the 7,500 lb Dexter DX7.5L A-60 Brake Actuator - Bolt On - Drum - 2" Ball #DX27FR.

view full answer...

Answer 3

To add a set of air bags to your 2024 Ford F-350 4WD, I recommend the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs item #F95FV. I really like the Firestone airbags because they use a crimp rolled design which is much more durable…

view full answer...

Answer 4

To add a set of air bags to your 2024 Ford F-250 4WD, I recommend the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs item #F95FV. I really like the Firestone airbags because they use a crimp rolled design which is much more durable…

view full answer...

Answer 5

The base or bezel used by the Bargman #47-84-527 Double LED tailllight is constructed of hard plastic, like the other rectangular lamps of this type. If you click the provided links, you can see a product demonstration and an install video. For…

view full answer...

Answer 6

We do have the following replacement spindles that will fit on your axle. #84 Spindle for 3,500-lb Trailer Axles - 2" Diameter #TRU24FR #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter #TRU84FR #84 Spindle for 3,500-lb Trailer Axles…

view full answer...

Answer 7

The #84 Spindle for 3,500-lb Trailer Axles part #TRU84FR and the Trailer Idler Hub Assembly for 3,500-lb Axles part #AKIHUB-550-35-K for a 5 on 5" wheel bolt pattern or the Trailer Idler Hub Assembly for 3,500-lb Axles part #AKIHUB-545-35-K for…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 10

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...