Options For Replacing Bulldog Square, A-Frame Jack # BD195318 With Heavier Capacity Jack
Question:
Mike L explained that the bolt pattern is different on this jack than the normal jacks. I found that out as I needed a higher capacity jack due to our tongue weight. I ordered a 1750290317 5000# Bulldog and the holes do not line up. Our trailer had been modified previously to take the BD195318. In doing so the original holes are now damaged and blocked by the nuts used on the BD195318 hole locations. Is there another square tube jack which has the same hole location as BD195318 but has a higher load capacity? This old jack works just not well. Thankya
asked by: Don F
Expert Reply:
The Bulldog Square, A-Frame Jack # BD195318 is a unique jack with its mounting pattern and we currently do not have any other a-frame jack with the same mounting pattern. To switch back to a jack like the Bulldog Round, A-Frame Jack # BD1750290317 you are going to want to replace your Coupler # CA5400 or weld in a new section to bolt the jack onto.
The other option is installing a jack like the Fulton # HD50000101 which will mount to the frame tube.
Products Referenced in This Question
Bulldog Round, A-Frame Jack - Topwind - 15" Lift - 5,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 4001 - 5000 lbs
- Topwind Jack
- 15 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- Bulldog
more information >
A-Frame Coupler with Oily Finish - 2-5/16" Ball - 14,000 lbs
- A-Frame Trailer Coupler
- Standard Coupler
- Weld-On
- 14000 lbs GTW
- 2-5/16 Inch Ball Coupler
- Thumb Latch
- etrailer
more information >
Fulton Boat Trailer Jack w/ Footplate - Fixed Mount - 28" Lift - Zinc - 5,000 lbs
- Trailer Jack
- Boat Trailer
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 4001 - 5000 lbs
- Sidewind Jack
- 28 Inch Lift
- Bolt-On
- With Rectangle Foot
- Fulton
more information >
Product Page this Question was Asked From
Bulldog Square, A-Frame Jack - Drop Leg - Topwind - 28-1/2" Lift - 3,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 2001 - 3000 lbs
- Topwind Jack
- 15 Inch Lift
- Bolt-On
- Weld-On
- With Rectangle Foot
- Bulldog
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Correct Method For Adjusting Tire Pressure On Long Road Trips
- Q&A: Recommended 2" Trailer Hitch And Wiring Harness For A 2024 Toyota RAV4 Prime
- Q&A: Replacement Tires For Utility Trailer That Uses ST205/75D14
- Q&A: Should Older Trailer Replace Breakaway Kit WIth One That Has Charger
- Q&A: Which Jounce-Style Suspension Enhancement Should I Install On 2020 Chevy Silverado 1500 Non Mag Ride
- Q&A: How Do I Secure A Kayak To My Roof When There Are No Anchor Points On The Front Of My Vehicle?
- Q&A: What is Overall Weight Capacity of Kenda Karrier ST235/80R16 Radial Trailer Tire with 16" Black Mod
- Shop: Bulldog Winch Portable Air Compressor - 100 psi - 1.2 cfm Maximum Air Flow - Automatic
- Search Results: 44649
- Video: Aries AdvantEdge Headache Rack Review
- Shop: MaxxTow MaxWorks Creeper Seat Toolbox - 350 lbs
- Article: Pintle-Hitches
- Shop: Trailer Hitch
- Video: Aries AdvantEdge Headache Rack Installation - 2021 Ford F-250 Super Duty
- Shop: Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs
- Article: Brake Controller Installation: Starting from Scratch
- Shop: Trailer Wiring
- Search Results: 68149
- Shop: Grease Seals 10-36 (pair)
- Article: Trailer Wiring Diagrams
- Video: Review of Gen-Y Hitch Dual Sway Control Bracket Adjustable Ball Mount 2" Receiver - 325-GH-300-1
- Shop: Fifth Wheel Hitch
- Search Results: 25580
- Search Results: led turn signal
- Shop: Gooseneck Hitch
- Shop: Rubber Bushing w/Steel Sleeve - 1" Inner Diameter - 2" Outer Diameter - 3" Long
- Article: Determining Trailer Tongue Weight
- Video: etrailer Magnetic Hitch Receiver Reducer Sleeve Review
- Shop: Suspension Enhancement
- Shop: Demco Hydraulic Brake Actuator w/ Electric Lockout - Disc - Zinc - 2" Ball - 7,000 lbs