Wiring 2007 Jeep Grand Cherokee For Brake Controller

Question

Question:

I am looking for a 2007 Jeep Grand Cherokee wiring adapter for a Tekonsha 90160 Primus IQ Brake Control.

asked by: George

0

Expert Reply:

The 2007 Jeep Grand Cherokee does not have the pre-wired port used for installation of a brake controller.

To install a brake controller on your 2007 Jeep Grand Cherokee with a factory 7-Way you will need to do some hard wiring. The wire Jeep provides is the electric brake output wire that goes back to the 7-Way trailer connector. This wire should be a light green wire that is behind the fuse box in the cab of the Jeep. It will connect to the blue wire on the brake controller.

You will need to wire the black, white, and red wires on the brake controller. Both the black and white wires will be routed through the firewall, into the engine compartment, and over to the battery. You will need the Draw-Tite Brake Controller Wiring Kit, part # 5506.

You can attach the black wire from the brake controller to the black wire in the duplex cable. Then attach the white wire from the brake controller to the white wire on the duplex cable. You will then need to route the duplex cable through the firewall to the battery. Separate the two wires and connect the white wire to the negative battery terminal. Check your brake controller instructions to see which size breaker is needed and either connect the black wire to the included 30-amp breaker, or use a 20-amp breaker, like part # 9506P. You will then need to connect a wire from the breaker to the positive battery terminal.

Use a circuit tester like part # PTW2993, to find the brake light wire on the stop light switch located above the brake pedal. Find the wire that carries a signal only when the brake pedal is pressed. Attach this wire to the red wire on the brake controller. That should complete the installation of the brake controller on your Grand Cherokee.

If your vehicle does not have a factory 4-Way connector or 7-way connector, you will need to install a 4-Way connector like the Tow Ready T-One Wiring Harness, part # 118425 and then hardwire the brake controller by using the Brake Controller 7- and 4-Way Installation Kit, part # ETBC7. The # ETBC7 kit will plug into the 4-Way and the remaining wires will need to be hardwired to your vehicle. I am including a link to installation instructions for the Tow Ready wiring harness and the # ETBC7 kit.

I have included a drawing that shows how the wiring is used on a brake controller you may find helpful.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

The lid of the Bright Way Trailer Breakaway ICU Kit with 12V, 5-Amp-Hour Battery, Charger, and Wire Loom #BW94FR that you referenced has a wiring diagram shown that details how it wires. Not seen is there is a single wire that runs up to running…

view full answer...

Answer 2

Replacing just the plunger portion of the Breakaway Switch #HM20010 is simple if you still have the plunger end. The plunger will simply reinsert into the switch, you may need to move the trailer to get the brakes to fully disengage as they will…

view full answer...

Answer 3

On this page (typically below the product links) there is a helpful link section that will have the install instructions fo the Hopkins Breakaway kit part #20400 that you referenced. I also attached an install video that shows the kit installed as…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...

Answer 9

To add a hitch to your 2024 Jeep Grand Cherokee L, I recommend the Draw-Tite item #DT42GR. This hitch is custom fit and bolts to your Jeep with included hardware. This is a class III hitch with a 2" receiver. It has a 7,500 lbs towing capacity…

view full answer...

Answer 10

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector…

view full answer...