How to Add a 7-Way and Brake Controller to a School Bus

Question

Question:

Hello, I have a 2001 Thomas Saf-T-Liner School Bus. Can you recommend products to wire up a 7-pin plug with a trailer brake controller?

asked by: Justin K

0

Expert Reply:

I sure can! To add a 7-way connector and a brake controller to your 2001 Thomas Saf-T-Liner you will first need to have a 4-flat connector. If you do not already have one you'll have two options depending on your buses lights. If the turn signals and brake lights use the same bulb you could install the 4-Way Flat Trailer Connector item # 18252. If your bus has amber turn signals that are separate from the brake lights you will need a converter. The Curt Tail Light Converter with 4-Way Flat Trailer Connector item # C56175 would be the best way to go.

To add the actual 7-way, I recommend the Universal Installation Kit for Trailer Brake Controller item # ETBC7. The kit includes a pre-wired 7- and 4-way trailer connector that mounts easily at the rear of your bus with an included bracket. This kit is designed for use on a vehicle with an existing 4-way flat trailer connector and plugs directly into it.

You will then connect the blue wire to the blue wire on the brake controller, connect the black wire to the positive post on the your battery, the white wire to ground, and the yellow wire to a reverse circuit if applicable. This will provide you with the ability to control your trailer's brakes and also provide you with a 12v power wire for you trailer's accessory lights.

For a brake controller, my personal favorite is the Redarc Tow-Pro Liberty item # RED24FR you were looking at. This is a proportional brake controller that automatically adjusts your trailer's braking based on the deceleration of your vehicle. The Liberty has a unique installation method where the main unit is concealed behind your dash and the only part visible is the control knob.

The Redarc has a 3-Axis accelerometer that measures deceleration in all directions for precise braking and smooth, uniform stopping action. It automatically adjusts the trailer's braking based on deceleration of your vehicle.

You will need the Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item # RED69FR to complete the installation.

expert reply by: Jerred H

0

Answer 1

In order to have both the tow dolly's and towed vehicle's lights active at the same time while being pulled behind a motorhome, the motorhome's trailer lighting circuits must be rated for the amp draw of both sets of lights.…

view full answer...

Answer 2

There is a way for you to add a trailer hitch to your 2002 Thomas Saf-T-Liner bus although there are none mounted vertically onto the frame, they will use brackets to mount to the frame which can be bolted or welded on. What you need is the Draw-Tite…

view full answer...

Answer 3

The Draw-Tite Max-Frame Trailer Hitch Receiver #75282 will have the following bolt hole dimensions for your 2015 Nissan Frontier. The Bolt holes from drivers side to passenger side frame rails are 43-5/8" on center. The holes running from front…

view full answer...

Answer 4

Yes, we do. I have attached them below. This hitch is confirmed to fit the 1985 Chevrolet C/K Series Pickup with the 6' or 8' beds with a standard or step bumper and the cab and chassis models.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

How to Add a 7-Way and Brake Controller to a School Bus

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching