Bolt Hole Dimensions For Mounting Draw-Tite Max-Frame Trailer Hitch Receiver # 75282

Question

Question:

What is the distance between bolt holes from side to side? My girl friend got one from another manufacturer and both were wrong for a 2015 Nissan Frontier sv crew cab. Thank you

asked by: Robert L

0

Expert Reply:

The Draw-Tite Max-Frame Trailer Hitch Receiver # 75282 will have the following bolt hole dimensions for your 2015 Nissan Frontier.

The Bolt holes from drivers side to passenger side frame rails are 43-5/8" on center. The holes running from front of the hitch to back are spaced 3-1/2" on center. I have included the picture with measurements for you to reference.

expert reply by: Bud M

0

Bolt Hole Dimensions For Draw-Tite # 75282
(click to enlarge)

Answer 1

The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" #75282 requires all hardware be torqued to 68 foot pounds according to the instructions. I've attached a photo in case you need anything else for this…

view full answer...

Answer 2

The spare tire carrier for E-Tracks, #RA-16HST, would hold and secure a spare outside of a trailer but it would not be ideal. The issue is that there will be some movement of the tire since the E-Track connection is not tight. It is secure, but…

view full answer...

Answer 3

So you will need to access the 12 pin jumper plug in your Frontier's cab, which as you said is on the passenger’s side behind the kick panel. This is where you will install the harness and relays that activate the trailer tow package, and the…

view full answer...

Answer 4

For your 2022 Nissan Frontier, I recommend Wiring Harness #C56225. As far as a hitch goes we do have a few options for your truck, however, I recommend one of best sellers, the etrailer Trailer Hitch Receiver #e98869. This is a custom made class III…

view full answer...

Answer 5

We can get your 2022 Nissan Frontier without the factory tow package set up with a 7-way and brake controller, and for the 7-way there is one part that is needed, though it will not be factory style, it will be a 7-way that you plug in and will…

view full answer...

Answer 6

It sounds like maybe your Curt #C15572 may have been slightly bent during shipping. If yours isn't lining up I can almost guarantee that is what happened. Some people will use open steps for leverage, vices and even car jacks to apply controlled…

view full answer...

Answer 7

I went out to our warehouse and measured the Curt Front Mount Trailer Hitch Receiver part #31026 for you. The distance between the bolt holes on center is about 37" left to right and 4-1/4" front to back. I have attached a photo with these…

view full answer...

Answer 8

I went out to the warehouse to take some measurements of Curt trailer hitch #C14082. I made a picture showing the measurements for you. The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of the…

view full answer...

Answer 9

We have not yet had a chance to test fit the Curt Front Mount Trailer Hitch part #C31013 on a vehicle specifically a Toyota Tacoma. So I would not be able to tell you exactly how much ground clearance is lost. However, I went out the warehouse and…

view full answer...

Answer 10

I sure can! To add a 7-way connector and a brake controller to your 2001 Thomas Saf-T-Liner you will first need to have a 4-flat connector. If you do not already have one you'll have two options depending on your buses lights. If the turn signals…

view full answer...

Answer 11

The inside to inside flange to flange distance of the #DT85MR Draw-Tite Class III hitch is 44 inches. Each mounting flange has 3 holes, the center hole is 2.87 inches from the mounting hole closest to the receiver tube, and the center hole and the…

view full answer...

Answer 12

I reached out to my rep at Curt and was able to get a couple of options for you. Both of these are going to require some modifications because there is no custom fit front hitch available for your 2012 Chevy Express 2500 Cutaway Van. Your best bet is…

view full answer...

Bolt Hole Dimensions For Mounting Draw-Tite Max-Frame Trailer Hitch Receiver # 75282

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching