Do Air Lift LoadLifter 7500 XL Fit 2022 Chevy Silverado 2500 With 5th Wheel Brackets

Question

Question:

Hi, I have a Chevy Silverado 2500HD 2022 and I need to know if the lift loader 7500XL will fit with my aftermarket fifth wheel bracket Curt 16429?

asked by: Frederic

0

Expert Reply:

They do not; the U-bolts for installing the # AL57541 occupy the exact same spot as the Curt brackets on your 2022 Chevy Silverado 2500. That said, we do actually have an option for 7,500 lb air bags, from Firestone:

- Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs # F2709

The # F2709 are compatible because they don't install with the U-bolt over the top of the frame, so there won't be any interference with 5th wheel brackets.

expert reply by: Kyle S

0

Answer 1

Yes, the Air Lift LoadLifter 7500 XL Air Helper Springs #AL57541 will work with your 2022 GMC Sierra 2500. These springs will work with both the 2 and 4 wheel drive variants and will provide up to 7,500 lbs of load leveling capacity.

view full answer...

Answer 2

The air spring kit I recommend for your 2020 GMC Sierra 3500 is the Firestone Ride-Rite Red Label #F2709. Firestone air bags are less likely to leak and overall more reliable thanks to their rolled crimp seal that keeps the bags securely anchored…

view full answer...

Answer 3

Timken bearing kits are made in the USA and they are much more reliable than other options. So since we know you have a 7k axle on your Forest River Riverstone the correct kit would be the part #TMK22VR.

view full answer...

Answer 4

I recommend the Air Lift LoadLifter 7500 XL Air Helper Springs - Rear Axle #AL57541. It offers individual manual air pressure adjustment to get the custom air ride you want. It can level a load from side to side and take pressure off your rear…

view full answer...

Answer 5

The Extang #EX48UV is a different model (E-Series) than the Trifecta 2.0 Covers #EX59KR and #EX37TR. The difference between the #Extang Trifecta 2.0 #EX37TR and #EX59KR is simply the material of the tarp. The #EX37TR has a vinyl cover while the…

view full answer...

Answer 6

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 7

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 8

I can definitely help you find the correct replacement hub and bearings for your Dexter P-12 SLR axle, but since part of the serial number was unreadable you will need to take a few simple steps to identify which bearings your axle uses. The easiest…

view full answer...

Answer 9

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...

Answer 12

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...