Does Reese Sidewinder RP34FR Work With Reese M5 5th Wheel Hitch?

Question

Question:

Reese M5 5th Wheel Trailer Hitch for Chevy/GMC Towing Prep Package - Single Jaw - 27,000 lbs Item # RP58FR Can someone confirm that this hitch would indeed work with the Reese sidewinder 20k Kingpin?

asked by: Rod W

0

Expert Reply:

Yes, the Reese Sidewinder 5th Wheel King Pin with Rotating Turret - 20,000 lbs # RP34FR is 100% compatible with the Reese M5 5th Wheel Trailer Hitch # RP58FR. The Sidewinder comes with the wedge you'd need, but in case you lost it or don't have it, you can buy another one here: Sidewinder Wedge Kit # RP44FR.

expert reply by: Andrew N

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 5

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 6

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 7

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 8

We still recommend the use of a slider in all standard/short bed trucks. That being said, the new GM trucks like your 2022 GMC Sierra 2500 do have a slightly longer bed than the typical standard bed. The best thing you can do is to measure to see if…

view full answer...

Answer 9

So for your set up, a 2021 Ram 2500 short bed with the RamBoxes, you will need to use a Sidewinder in order to have the clearance to tow a 5th wheel. The Goose Box doesn't move the pivot point and an offset ball just won't be enough for…

view full answer...

Answer 10

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Answer 11

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 12

Yes. You will have to use the Demco Hijacker Autoslide Capture Plates for Trailair Rota-Flex Pin Boxes #DM6171 on your 2021 Grand Design Reflection 337RLS. As far as which Curt Flexair works for your trailer, it depends on what pinbox you currently…

view full answer...