Can Bearings Be Packed with Grease From Small Side

Question

Question:

when i packed my bearing i push the grease in from the small side of the bearing is that ok.

asked by: William

0

Expert Reply:

As long as you're seeing grease pushing out the larger end of your Timken Bearing Kit # TMK52VR when you pack the bearings you'll be good to go!

We typically go from the larger end just because it's easier to pack the bearings that way, but the main thing is making sure the bearing is full of grease for the best trailering experience.

If you have any other questions about bearings please feel free to reach out, William!

expert reply by: Jon G

0

Answer 1

You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

Installing the Union Tee #AL21838 with your #AL57575 will tie the pressure of the two air bags together. So yes, a shift in a very heavy load like a truck camper will potentially result in air being forced from one into the other. The reason I say…

view full answer...

Answer 8

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 9

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 10

If you have a trailer wheel that has a 6 lug setup you are going to have a bolt pattern of 6 on 5-1/2 inches. This is the standard 6 lug wheel bolt pattern that trailer rims have. If you are unsure you can check out the help article I attached that…

view full answer...

Answer 11

There really should be a flat washer between the outer bearing of your hub and the nut that holds it on. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. The Washer For 1 inch Spindle,…

view full answer...

Answer 12

The ALKO 4,400 lb axles use the same bearing sizes as the standard 3,500 lb alxes. If you want USA made bearings, I recommend the Bearing Kit #TMK52VR. This kit comes with the Timken brand bearings which are all made here in the USA.

view full answer...

Can Bearings Be Packed with Grease From Small Side

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching