2 inch Lift for 2019 Crossroads Volante

Question

Question:

Hi, I want o upgrade my leaf springs on my 2019 crossroads volante. Id like about 2 of lift, but dont have OEM specs. suggestions?

asked by: Gary R

0

Expert Reply:

There's a simpler way to get a 2 inch lift for your 2019 Crossroads Volante with the Correct Track tandem lift kit part # RR23QX which does not require you to replace your current springs. This will give you a lift of 2-1/8 inches.

If you want new leaf springs you'd need to know the axle capacity of your trailer and the current length of the axles.

expert reply by: Jameson C

0

Answer 1

I checked directly with Dexter, and from what I saw they have a measurement - taken from center of spring eye to center of spring eye - of 24.8", which is the same as our 24-7/8" measurement for the 7-Leaf Double-Eye Spring for…

view full answer...

Answer 2

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the…

view full answer...

Answer 3

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower…

view full answer...

Answer 4

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 5

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 6

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 7

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 10

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

Answer 11

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 12

Hey Patrick, so for your leaf spring upgrade I am going to need to know a couple of things before I can get you over to the right part. Specifically, the length from eye to eye, the spring width, leaf thickness, and the number of leaves. From here I…

view full answer...

2 inch Lift for 2019 Crossroads Volante

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching