Can the etrailer Bolt-On Swivel Mounting Plate # e52JR Be Welded On?

Question

Question:

Can this be welded on?

asked by: Pam H

0

Expert Reply:

Yes, the etrailer Bolt-On Swivel Mounting Plate # e52JR can be welded on as long as you properly prepare the surfaces.

expert reply by: Bud M

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex…

view full answer...

Answer 3

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 4

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 7

In order to match up the wheel studs for your Reliable 1206 hub, we'll need to know the full dimensions of the wheel stud you're replacing. In addition to the total length of the stud and its diameter and thread pitch, we'll also need to…

view full answer...

Answer 8

The Buyers Products 45 Ton Pintle Hook #337PH45 does not have the 4 inch square bolt pattern but rather uses a different pattern. Vertically the holes are 3 inches on center. Horizontally the top row is 5-1/4 inches on center and the bottom is 6-1/2…

view full answer...

Answer 9

I believe I have a solution for you, but I think you may need to remeasure your cutout and/or compare the measurements of your current latch with one of ours. Since latches tend to be fairly universal in size when it comes to the RV world the Global…

view full answer...

Answer 10

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 11

The Hayes Air Actuated Trailer Brake Controller - 1 to 4 Axles - Proportional #HA100400C mounts to the inside of your 2007 Nemar Essex at the dash just like other electric brake controllers will. It needs to be installed on the inside of the vehicle…

view full answer...

Answer 12

The crank handle for the Lippert Components Spare Tire Winch with Offset Cable item #LC159056, is Replacement Crank Extension for Lippert Spare Tire Winch Assemblies - 35-1/2" item #LC1315411. The Spare Tire Winch item #LC159056 has a 1/2-inch…

view full answer...

Can the etrailer Bolt-On Swivel Mounting Plate # e52JR Be Welded On?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching