Will the In Bed Trunk On a 2023 Honda Ridgeline Still Open With BAKFlip G2 Tonneau Cover Installed?

Question

Question:

does the g2 interfere with trunk cover opening on a 2023 Ridgeline

asked by: Jack D

0

Expert Reply:

You will still be able to open and use your in bed trunk on your 2023 Honda Ridgeline with the BAKFlip G2 Hard Tonneau Cover # BAK26602 installed. Do note when the tonneau cover is closed this will greatly limit how far the trunk will open so you may only be able to retrieve small items from the trunk area.

expert reply by: Bud M

0

Answer 1

Yes. The RedArc Tow Pro Liberty #RED24FR is a great choice since it installs out of the way and provides you with proportional braking for your tandem axle trailer. You'll want to use the Plug-and-Play Wiring Harness for Redarc Tow-Pro…

view full answer...

Answer 2

It's very easy to install a trailer brake controller on a 2021 Honda Ridgeline. I recommend the Tekonsha Prodigy P3 Trailer Brake Controller part #90195 which comes with a harness that you could simply attach to the one that came with the…

view full answer...

Answer 3

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex…

view full answer...

Answer 4

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 5

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 9

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 10

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 11

Actually our etrailer.com brand brake assemblies are rebranded AxleTek assemblies. So we have the 8k left and right assembly set #AKEBRK-8 which is most likely what you need but these are 12-1/4 inch in diameter by 3-3/8 inches wide and attach with a…

view full answer...

Answer 12

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Will the In Bed Trunk On a 2023 Honda Ridgeline Still Open With BAKFlip G2 Tonneau Cover Installed?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching