Where to Weld Tandem Axle Trailer Fenders w/ Backing Plates

Question

Question:

If the backing plate isn't supposed to be welded to the trailer then how do I weld this?

asked by: Cathy

0

Expert Reply:

There is a flange on the Tandem Axle Trailer Fenders w/ Backing Plates # HP82VR that overlaps the backing plate that you'll use for the welding surface.

When it comes to welding, we always recommend having this done by an experienced welder.

expert reply by: Jon G

0

Answer 1

I have attached a photo for you below that shows which way the s-hooks should face when attached to the safety chain loops on a trailer hitch. The photo example is using the Curt Single Hook, Coiled Safety Cables with S-Hooks part #C80176 for…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

There is a flange on the Tandem Axle Trailer Fenders w/ Backing Plates #HP82VR that overlaps the backing plate that you'll use for the welding surface. When it comes to welding, we always recommend having this done by an experienced welder.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

The backing plate on the Tandem Axle Teardrop Fenders #HP92VR is 12" down from the top of the fender.

view full answer...

Answer 7

Thanks for the picture! For your 2023 GMC Sierra 1500 with adaptive ride control you'll want the Air Lift LoadLifter 5000 Air Helper Springs item #AL57388. This air bags have a 5,000 lbs load leveling capacity that will keep the rear end of your…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

I have a solution for you Travis as Pace Edwards does not offer a contractor rack for your 2023 GMC Sierra 1500. Instead you can use the Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover #311-M-FMCA28A59 with the Thule TracRac SR…

view full answer...

Answer 11

Hello Steve. I do have a good solution for you, but I cannot recommend using the Malone Adapter #MPG544. Since it is rated for towing only 4,000 lbs, your 8,000 lb towed vehicle would be double the max towing capacity. You are right about there being…

view full answer...

Answer 12

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Where to Weld Tandem Axle Trailer Fenders w/ Backing Plates

Product Page this Question was Asked From

Continue Researching