Can Reverse Lockout Solenoid Be Installed on DA91 Demco Hydraulic Brake Actuator

Question

Question:

Can I install a solenoid valve on this model so as not to have a problem with reverse?

asked by: Juan N

0

Expert Reply:

Yes, you can definitely add a solenoid to the Demco Hydraulic Brake Actuator # DM8509202 so your brakes don't activate when you put your vehicle and trailer in reverse. What you're looking for is the Reverse Lockout Solenoid # DM11993.

Just be sure to install a 5-Way connector on both your trailer and your tow vehicle so you can get that reverse function to the solenoid. If you don't already have these then we have the Hopkins Kit # HM47890 you can use to accomplish this.

expert reply by: Jon G

0

Answer 1

Hi there Rich; while it doesn't come with one, there is a way to add an electric lockout to the Demco Hydraulic Brake Actuator w/ Drop - Drum #DM8669112. All you need to do is add the Reverse Lockout Solenoid for Demco Hydraulic Brake Actuators -…

view full answer...

Answer 2

Thank you for the picture, it is helpful. I can see that you have an actuator for disc brakes. In the picture you can see the yellow label that says "disc brake actuator for use with disc brakes only". The coupler does not differentiate…

view full answer...

Answer 3

The best replacement option we have for a Titan Surge-O-Matic is the Titan Zinc-Plated Brake Actuator part #T4750600 which is rated for disc brakes and can support up to 12,500 lbs. It also has the same drop coupler design as the one you have now so…

view full answer...

Answer 4

To bleed the Titan Zinc-Plated Brake Actuator w/ Drop part #T4750600 using the lockout arm isn't the way to go. What I prefer to do is use a larger 5 foot piece of 2x4 you will place this up against the ball coupler and loop the safety chains…

view full answer...

Answer 5

The only way to turn a surge brake actuator "off" is to engage a lockout on the actuator. Some actuators have manual lockouts, others have electric lockouts, and some have no way to lock out the actuator. Typically, free-backing brakes are…

view full answer...

Answer 6

The reverse lockout solenoids stop brake fluid from being released from the master cylinder and sent to the wheel cylinder. It does this by receiving an electric signal, usually from the reverse light circuit. That said, if you were to wire this into…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...