Can Prodigy P3 Brake Controller Replace OEM Controller of 2016 Toyota Tundra

Question

Question:

I have a 2016 Tundra trailer brake controller is not working. Toyota said it needs to be replaced. If I replace with a non OEM, are there updates required to tye computer..ecm...? What do u have that would be compatible?

asked by: George A

0

Expert Reply:

If you replace the OEM Brake controller of your 2016 Toyota Tundra with the Prodigy P3 part # 90195 and install harness part # 3031-P you would just need to disconnect the vehicle battery for a minute or so to prevent any dash error codes.

expert reply by: Jameson C

0

Answer 1

You can use the Furrion Vision S with Side Cameras kit part #FCE48TASL-05 on your Coachman Apex travel trailer that was pre-wired for a Voyager but there isn't an adapter available. Instead all you'd need to do is remove the wiring to the…

view full answer...

Answer 2

With this problem the issue is almost always that the pins of the 7-way need to be cleaned with sandpaper. The brake controller output circuit on the 7-way is the 5:00 position of the vehicle side.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

Can Prodigy P3 Brake Controller Replace OEM Controller of 2016 Toyota Tundra

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching