Recommended Ladder Rack for a 2024 Ford Maverick

Question

Question:

I have a 2024 Ford Maverick I use around town to haul PVC, 2x4's, and the occasional ladder. I am interested in getting a ladder rack for the back of my truck but do not want to drill into my bed

asked by: Jessica

0

Expert Reply:

To add a ladder rack to your, 2024 Ford Maverick, I recommend the is the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack item # Y01151-57.

The Yakima ladder rack system has a no drill installation and a 500 lbs capacity. The system attaches to the side of your bed rails using screw down clamps like you would use to attach a camper shell. Each upright is held on by two.

I have linked an installation video below so you can see how to get this ladder rack set up and some of its features demonstrated.

expert reply by: Jerred H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 3

You have a good eye Richard, as there is not a difference between the etrailer and Demco base plates that fit your 2024 Ford Maverick: - etrailer Invisible Base Plate Kit e64FV - Demco Tabless Base Plate Kit #DM77YV Both will fit your '24…

view full answer...

Answer 4

The best adjustable height ladder rack for your 2023 Ford Maverick that is compatible with a tonneau cover is the Yakima OverHaul HD part #Y01151-57555. This comes with adapters designed to fit the T-slots of the RetraxONE XR part #RTX83QR which is a…

view full answer...

Answer 5

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 6

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 7

The Telescoping Rack for TruXedo Elevate Rack System #TX24NV uses crossbars which are 3.79" wide, 1-1/2" tall and 67" long.

view full answer...

Answer 8

Okay Bob, so I did a bit of digging around and apparently this is a known issue that Blue Ox is aware of. The 41" distance between the mounting points is too wide and non-standard which is why your tow bars are being stretched too far.…

view full answer...

Answer 9

In regards to the base plate kit options for a 2022 Ford Maverick, the Blue Ox Base Plate Kit part #BLU88XR requires the least amount of modifications as there is no cross tube like on the Roadmaster Direct-Connect Base Plate Kit part #RM97RR. That…

view full answer...

Answer 10

Although it's not said, to install the Demco Tabless Base Plate Kit #DM77YV there may be some trimming of spoiler, air dam, grille or plastic fascia required depending on the model of this vehicle. To complete your flat towing setup, you're…

view full answer...

Answer 11

Yes, it does! The Yakima OverHaul HD Adjustable Truck Bed Ladder Rack item #Y01151-57 has been confirmed to fit the 2024 Ford Maverick. This ladder rack system has a no drill installation and a 500 lbs capacity. The uprights heights can be adjusted…

view full answer...

Answer 12

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...