Will The Rack'Em Double Barrel Utility Trailer Tailgate Lift Assist Work On A Horse Trailer

Question

Question:

I have a small 2-horse trailer with a ramp. The ramp is super heavy for me to down and lift up. Will the rack-em double barrel work on my trailer or do I need something different.

asked by: Julie K

0

Expert Reply:

It really depends on the style of your trailer. If you have an open trailer with side rails that could attach the Rack'Em Double Barrel Utility Trailer Tailgate Lift Assist # RA-27C to then yes, you could use it. If you have an enclosed horse trailer then you would need to install an appropriately sized ramp door spring, like part # ERS160D96, to help lift and lower the ramp door.

expert reply by: Kevin C

0

Answer 1

You wouldn't use a spring like #RS16933LH because it produces 2,000 foot pounds of torque and you would not be able to open the ramp. What I recommend is either the Rack'em Double Barrel tailgate assist, #RA-27C. The Double Barrel will reduce…

view full answer...

Answer 2

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...

Answer 3

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 4

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 5

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 6

Thanks for the picture of what you have and the info you listed. The correct wheel you need is the part #AM20794 that you referenced.

view full answer...

Answer 7

That is an excellent question and is asked more often than you think. Electric brakes like what come in the Electric Trailer Brake Kit #AKEBRK-2 can be submerged in water when you are loading/unloading your boat. Since water and electricity don't…

view full answer...

Answer 8

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 9

In order to charge your batteries wired in parallel with the NoCo Genius #329-GENIUS5 you'll want to connect the positive charge line to the positive terminal of the first battery and the negative line to the negative terminal of the opposite…

view full answer...

Answer 10

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check…

view full answer...

Answer 11

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Will The Rack'Em Double Barrel Utility Trailer Tailgate Lift Assist Work On A Horse Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching