Replacement Oil Seal for 13" Kodiak Disc Brakes

Question

Question:

Whats the correct oil seal for this? I always like to have extra seals on hand so I don't have to wait to make any repairs.

asked by: Philip

0

Expert Reply:

To replace the oil seal on the 13" Kodiak Disc Brakes # KOD77VR you need the part # XLPROLUBE2440SEAL.

It's an excellent idea to keep spare of these common replacement parts to make projects quicker like you said.

expert reply by: Jon G

0

Answer 1

I did a bit of searching online and called a few grease seal manufacturers but was not able to reference "AF3531G" to any particular product. Therefore, the only way you are going to be able to find the correct replacement would…

view full answer...

Answer 2

We sell Kodiak hub and rotor kits like the part #KOD66FR which you could use to piece together a conversion kit for your 2016 Keystone Fuzion 345 which has 7k axles but we do not have kits that include all of the components needed from Kodiak. The…

view full answer...

Answer 3

The Kodiak Disc Brakes #KOD33FR are the brakes you will need to convert your 7,000lb axles to use disc brakes. This kit provides the brake assemblies for one axle so you will need 2 kits for your 5th wheel. It fits a standard #42 spindle with a…

view full answer...

Answer 4

I contacted Dexter and the Unitized Oil Seal for Trailer Hubs part #10-63 do not require RTV sealant or a gasket maker. They are typically used in oil bath hubs. I have attached an installation video for your reference.

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Replacement Oil Seal for 13" Kodiak Disc Brakes

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching