Mounting Bracket Hole Spacing for the Rhino Rack Sunseeker & Batwing Awning

Question

Question:

What are the distances between each of the three mounting holes on the rear of the bracket please? Thanks.

asked by: Howard D

1

Helpful Expert Reply:

The three holes on the back of the Rhino-Rack Sunseeker and Batwing Awning Mounting Bracket for Pioneer Platform Rack # RR43259 are spaced 1" on center.

expert reply by: Bryce D

1

Mounting Bracket Hole Spacing for Rhino Rack Sunseeker/Batwing Awning
(click to enlarge)

Answer 1

I would be happy to! We have taken quite a few measurements of the brackets for the Mounting Kit for Rhino-Rack Batwing Awning item #RR25FJ. Pretty sure the spacing you're asking for is 1-3/8" but there are a lot of holes so I went ahead and…

view full answer...

Answer 2

I attached a picture that has the dimensions of the brackets of the Mounting Kit for Rhino-Rack Batwing Awning #RR25FJ that you referenced.

view full answer...

Answer 3

The Rhino-Rack Heavy-Duty Roof Rack Roof Rack have specific C-channels that are designed to fit specific Rhino-Rack Heavy-Duty accessories, like the Rhino-Rack Hi-Lift Jack and Shovel-Holder Brackets #RRRCB-RSHB-RJHB as an example. That's the…

view full answer...

Answer 4

The two holes on the metal spacer block that are included with the Rhino-Rack Foxwing and Sunseeker Awning Mounting Bracket part #RR43259 are spaced 1" apart on center. I called my contact at Rhino-Rack to confirm this.

view full answer...

Answer 5

There is a solution available for you, but the #RR31103 will not work for you. It looks like ARB manufactures a T-slot adapter for their BASE Rack, and the Rhino-Rack Batwing Awning #RR33200 can be mounted into t-slots on a roof rack-which is what…

view full answer...

Answer 6

The dimensions of the top T-channel in Rhino-Rack Vortex Aero Crossbars like #RRVA126B-2 measure 0.25 inches deep x 0.86 inches wide inside the channel. The top of the channel measures 0.43 inches wide. As for the hardware that installs in to the…

view full answer...

Answer 7

On the portion of the Rhino Rack Awning Bracket part #RR31103 that you referenced that holds the awning the holes are 1-3/8 inches apart from left to right and 4-1/2 inches from front to back.

view full answer...

Answer 8

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 9

The ALKO 4,400 lb axles use the same bearing sizes as the standard 3,500 lb alxes. If you want USA made bearings, I recommend the Bearing Kit #TMK52VR. This kit comes with the Timken brand bearings which are all made here in the USA.

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hello Jeffrey, While I'm sure we have a bearing kit for your car trailer, we don't have any way of knowing off-hand or cross-referencing what bearings you need. You mentioned you have them out, so you should be able to see the part number…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Mounting Bracket Hole Spacing for the Rhino Rack Sunseeker & Batwing Awning

Product Page this Question was Asked From

Continue Researching