Replacement Hub/Drum for Traileir with 5,200 lb Axles

Question

Question:

i have a gooseneck flat bed trailer i know the axles are 5200lb. My hub broke off, how do i figure out which hub and wheel i need? Its a lamar trailer if that helps

asked by: Jeremy

0

Expert Reply:

Since we know you have a 5,200 lb axle on your Lamar trailer the correct replacement hub/drum would be the part # AKHD-655-6-EZ-K. To pick out a replacement wheel and tire I would need to know the size of your current tire sidewall.

expert reply by: Jameson C

0

Answer 1

The Locknut needed is 7/16 X 20 like the #006-092-01. This is a fit for the Replacement Shackle Link with Bolts for Dexter Trailer Suspension Kits #018-026-05 because the bolt tapers from 9/16 inches down to that 7/16 inches that is threaded.

view full answer...

Answer 2

The 2021 Grand Design Imagine 3250BH can come from the factory with either 3,500 lb, 4,400 lb, or 5,200 lb axles. If you have 5 lug hubs then that means you have 3,500 lb axles and need the Dexter Nev-R-Adjust Electric Trailer Brake Kit part…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

It really just depends on what you are looking to get out of the bushings. Bronze bushings, like part #K71-291-00, will last longer but are more noisy and it is recommended to use wet bolts like part #126B2 to keep them lubricated. Nylon bushings,…

view full answer...

Answer 7

I'd be happy to help you out, John! To replace the brakes on your 5th wheel trailer you need the etrailer Electric Trailer Brakes #AKEBRK-7-SA which come with a self-adjusting feature so once you initially set them up you won't have to adjust…

view full answer...

Answer 8

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 9

Hello Brian, we do offer some parts that will work for your application and will be very similar to the BPH1206EPR kit that you mentioned. Like you said, the 12 x 2-1/2 drums are pretty uncommon, so I would have to recommend going instead with the…

view full answer...

Answer 10

We've got you covered! To replace your wheel bolts you need the Dexter Wheel Bolt #7-262 which is a 1/2" diameter and 2-11/16" long. Since your hub and drum assembly looks to be pretty worn though I recommend just replacing the whole…

view full answer...

Answer 11

You shouldn't really have any play with the Easy Grease Trailer Hub and Drum Assembly #AKHD-655-6-EZ-K. If you are getting play in it then the bearings most likely are either not set correctly or were the incorrect choice for your axle's…

view full answer...

Answer 12

Thanks for the information on your trailer. For your axle with brakes I recommend the Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb E-Z Lube Axles - 12" - 6 on 5-1/2 #AKHD-655-6-EZ-K if you have the spindles with the integrated grease…

view full answer...

Replacement Hub/Drum for Traileir with 5,200 lb Axles

Product Page this Question was Asked From

Continue Researching