Replacement Recommendation for Dexter Axle 8-201 Hub Assembly on Older Horse Trailer

Question

Question:

I have an old horse trailer ~2001? with Dexter P-15 Model SLR axles SN D-6387239 and 8-201 hubs. I think the wheel was put on loose by *someone* and it rattled until it broke all the studs off. I can put new studs in if you can point me in the right direction on a stud/nut set, but Im also curious what the right replacement axle assembly would be if I want to just swap out the entire axle.

asked by: Nathan C

0

Expert Reply:

We've got you covered!

To replace your wheel bolts you need the Dexter Wheel Bolt # 7-262 which is a 1/2" diameter and 2-11/16" long. Since your hub and drum assembly looks to be pretty worn though I recommend just replacing the whole thing so you have completely new bearings and a seal as well. To replace the whole drum assembly you'll need part # 8-201-5UC3-EZ.

The bearings that come with this kit match your application (I checked with my contact at Dexter Axle) but you will want to measure the spindle where the grease seal sits and ensure that is 2.125" diameter so we know this grease seal matched exactly.

When it comes to a replacement axle, you have a torsion axle so the only replacement we have is from Timbren with their kit # ASR5200S01. If you ended up going this route then you'll want the Easy Grease Trailer Hub and Drum Assembly # AKHD-655-6-EZ-K instead because it comes with a grease seal that has a 2.250" inner diameter.

You can also swap out your brakes with part # AKEBRK-7-SA for an electric kit or part # AKFBBRK-7 if your trailer has hydraulic brakes.

expert reply by: Jon G

0

Axle Tag on Oler Horse Trailer
(click to enlarge)

Dexter 8-201 Hub and Drum Assembly on Horse Trailer
(click to enlarge)

Answer 1

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the…

view full answer...

Answer 2

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

I'd be happy to help you out, John! To replace the brakes on your 5th wheel trailer you need the etrailer Electric Trailer Brakes #AKEBRK-7-SA which come with a self-adjusting feature so once you initially set them up you won't have to adjust…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

Hello Brian, we do offer some parts that will work for your application and will be very similar to the BPH1206EPR kit that you mentioned. Like you said, the 12 x 2-1/2 drums are pretty uncommon, so I would have to recommend going instead with the…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

The inner diameters of the LM67048 and 15123 both are the same (1.250 inches). That means that a hub with either bearing in the outer bearing would fit your spindle. The part #AKHD-655-6-EZ-K would fit your axle.

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

If you already have brake drums you will not have to replace them unless they are damaged or became overheated and have discoloration on the inside armature surface where the magnet rides, grooves in the armature surface, or severe wear where the…

view full answer...

Replacement Recommendation for Dexter Axle 8-201 Hub Assembly on Older Horse Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching