Recommended MORryde Pin Box to Replace a Rhino Pin Box

Question

Question:

Hello, I just have one question or maybe two. I have a 2023 jayco eagle 335RDOK, with a Rhino pin box. I just want to make sure the Morryde rubber pin box is the right one for my trailer. Also, I have a pull rite superglide 5th wheel hitch. Can you confirm the correct adaptor/capture plate for this Morryde rubber pin box. Thanks

asked by: Nathan

0

Expert Reply:

The MORryde Cushioned 5th Wheel Pin Box item # MR83QR is the correct pin box for your 2023 Jayco Eagle. This one is specifically designed to fit the Rhino pin box.

The correct adapter kit is the MORryde Pin Box Adapter for PullRite SuperGlide Hitch item # MR57ZR.

expert reply by: Jerred H

0

Answer 1

We do have an Autoslide fifth wheel hitch that may work for you. It is the Demco Hijacker, part #DM8550034. I called my contact at Demco and asked about disconnecting and the angle it can be detached. They told me that there is a 10 degree angle…

view full answer...

Answer 2

Yes, MORryde cushioned pin boxes like #MR84VR can be used with Demco Hijacker Autoslide fifth wheel hitches. There's even a capture plate from MORryde that was designed for this application with the part #DM6025.

view full answer...

Answer 3

The Rhinobox was definitely an unpopular choice for manufacturers to go with so swapping it out with the MORryde Cushioned 5th Wheel Pin Box for 18K to 21K Trailers w/ Lippert Rhino #MR55QR would definitely give you a major improvement in ride…

view full answer...

Answer 4

The dimensions of the base of the Demco Hijacker Autoslide 5th Wheel Trailer Hitch #DM8550034 are approximately 35 inches long x 31 inches wide. It has a height that can be set at 15-1/4 inches, 16-1/2 inches or 18 inches. The recommended cover for…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...