Would the 2-Piece Polypropylene Trailer Vent # WHMAV2-WAVT2 fit a 2 in Thick Wall

Question

Question:

Will the half-moon vent fit through a 2inch thick wall on my pop-up trailer?

asked by: Wade W

1

Helpful Expert Reply:

Yes it will, the 2-Piece Polypropylene Trailer Vent # WHMAV2-WAVT2 that you referenced would work on a 2 inch thick wall. You would just need to cut a 3 inch diameter circle hole in that wall and attach either side of the # WHMAV2-WAVT2 and it would function just fine.

expert reply by: Jameson C

1

Answer 1

If you mount the Redline 2-Piece Polypropylene Trailer Vent #WHMAV2-WAVT2 with the exterior part's flat slotted side facing forward (to increase air flow) there will definitely be a greater probability for rain and splashed water to enter the…

view full answer...

Answer 2

In regards to the 2-Piece Polypropylene Trailer Vent part #WHMAV2-WAVT2, I must recommend you install the vent using both the inside and outside components. If the wall thickness is too much to use the vent as is, all you will need to do is take a…

view full answer...

Answer 3

On the 2-Piece Polypropylene Trailer Vent, #WHMAV2-WAVT2, I would mount it near the top front of the trailer with the vent openings pointed down or towards the rear of the trailer. Ultimately, it does not really matter. Use some self-tapping screws…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 9

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

The 12 inch tires that we carry are rated for 65 miles per hour. Any faster than that for extended periods and the excessive heat build up will cause tire failure. To get a tire with a higher speed rating you would have to go up in size. That also…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Would the 2-Piece Polypropylene Trailer Vent # WHMAV2-WAVT2 fit a 2 in Thick Wall

Product Page this Question was Asked From

Continue Researching