Determining The Correct Replacement landing Gear Set For A 1995 Fleetwood Terry 5th Wheel Trailer
Question:
What landing jacks do I need for a 1995 Terry by Fleetwood 5th wheel 32.5 ft
asked by: Michael D
Expert Reply:
To determine the correct replacement landing gears for your 1995 Fleetwood Terry you'll want to measure the inside to inside and outside to outside measurement of the weld stops on your current landing gear set so we can see if there's a match that can just reuse your current mounting brackets. If there isn't you would have to cut off he current brackets and have a qualified welder weld on new brackets, which can drastically increase the cost.
The standard for most landing gear sets is 15-1/2" from bottom of upper weld stop to top of lower weld stop and 17-1/2" from top of upper weld stop to bottom of lower weld stop. If this is the case for you then you could use one like the Landing Gear Set w/ Handle # RVLG-8HDL along with the motor # LC142178.
let me know what your measurements are and I'd be happy to find a replacement for you.
Products Referenced in This Question
Lippert Venture 5th Wheel RV Landing Gear Motor
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Motor
- Lippert
more information >
Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 36 Inch Lift
- Weld-On
- 2 Jacks
- etrailer
more information >
Product Page this Question was Asked From
Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- Landing Gear
- 38 Inch Lift
- Weld-On
- 2 Jacks
- Ultra-Fab Products
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: atwood landing gear
- Search Results: stromberg carlson
- Search Results: 5th wheel landing gear
- Shop: Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Shop: Stromberg Carlson Manual Landing Gear Set - Weld On - 34-7/8" Lift - 8,000 lbs
- Shop: Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs
- Shop: Lippert Manual Landing Gear Set with Handle - Weld On - 37" Lift - 6,000 lbs
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Shop: Replacement Follow Leg for Stromberg Carlson Landing Gear - 33-1/2"
- Q&A: Replacement for Atwood Landing Gear on 2004 Fleetwood Wilderness 5th Wheel Trailer
- Q&A: Landing Gear Replacement Recommendation for 1997 Fleetwood 5th Wheel w/ RBW Landing Gear
- Q&A: Bracket Dimensions of the etrailer RV Landing Gear System # RVLG-8HDL
- Q&A: How to Determine Correct Replacement Landing Gear
- Q&A: Can the Follow-Leg Be Replaced On an Atwood Landing Gear Set
- Q&A: How To Confirm Fit of the Landing Gear Set with Handle part # RVLG-8HDL
- Q&A: Replacement 5th Wheel Landing Gear for 1999 Fleetwood Terry 5th Wheel
- Search Results: 44649
- Video: etrailer Landing Gear Set Review
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 25580
- Shop: Trailer Wiring
- Video: Choosing the Right Trailer Wiring
- Search Results: 68149
- Shop: Fifth Wheel Hitch
- Article: Trailer Tire Sizing
- Search Results: dust cap
- Shop: Gooseneck Hitch
on Trailer Jack
