Bearing Kit for 2014 Forest River Shamrock 23IKSS

Question

Question:

What bearings do I need for my 2014 Forest River Shamrock 23IKSS?

asked by: Mike R

0

Expert Reply:

Since we know your 2014 Forest River Shamrock 23IKSS has 3,500 lb axles the bearing kit you would want is the # BK2-100 which comes with bearings # L44649 and # L68149.

expert reply by: Jameson C

0

Answer 1

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 8

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 9

Overpacking the trailer hub with grease is the number one reason for grease seal failure. For a boat trailer I would recommend re-packing the hubs by hand with grease once per season and you'd be fine. I don't like recommending people use…

view full answer...

Answer 10

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 11

The inner diameters of the LM67048 and 15123 both are the same (1.250 inches). That means that a hub with either bearing in the outer bearing would fit your spindle. The part #AKHD-655-6-EZ-K would fit your axle.

view full answer...

Answer 12

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage…

view full answer...

Bearing Kit for 2014 Forest River Shamrock 23IKSS

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching