Could 4.80-12 Tire Size Fit on Same Wheel as 155R12

Question

Question:

Can I put a 4.80x12 tire on a rim that currently has a 155r12 on

asked by: Ron

0

Expert Reply:

Yes, a 4.80-12 tire like the part # TT48012C can fit on same wheel as a 155R12.

expert reply by: Jameson C

0

Answer 1

Yes, the #84 E-Z Lube Spindle w/ Brake Flange #TRU77FR will fit the 2" schedule 40 pipe.

view full answer...

Answer 2

I checked with Trudyde, and I was able to find out that the bar stock material used to make the spindle #TRU77FR is hot rolled SAE 1045 steel which is a medium carbon common steel grade.

view full answer...

Answer 3

The TruRyde #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axles item #TRU77FR has a 3" inner diameter. The E-Z Lube spindle welds onto your 3,500-lb trailer axle it works with L68149 inner bearing and L44649 outer bearing. The Stub…

view full answer...

Answer 4

A 155/80-12 is definitely not a common trailer tire sized, though it may have been at one time. It sounds more like a car tire size which should not be used on a trailer. The trailer tongue or frame should have a sticker or plate that indicates the…

view full answer...

Answer 5

Most likely your trailer has brakes, but not every single trailer out there does have them. I did some checking though and your Karavan KHD-2990-72-12-PR does have a set of 10 inch brake drums installed so you'd just need a brake controller…

view full answer...

Answer 6

The largest diameter drum that can fit behind a 12 inch trailer wheel is a hub/drum designed to fit a 7 inch diameter brake assembly like the #8-257-5UC3. That said the different size hub/drums all fit different size spindles. So you have to first…

view full answer...

Answer 7

Wheels fit based on bolt pattern as well as height and width. Your 5.30-12 wheels are 12 inches by 4 inches and upgrading to a 14 inch wheel will come with an increased width of 5.5 or 6 inches to go with the extra 2 inches of height. If you have…

view full answer...

Answer 8

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Could 4.80-12 Tire Size Fit on Same Wheel as 155R12

Product Page this Question was Asked From

Continue Researching