Recommended 7-Way Connector for a 2023 Subaru Outback Wagon

Question

Question:

I just bought a small trailer and need to add a 7-way connector to my 2023 Outback Wagon. What part or parts do I need to do this?

asked by: Von R

0

Expert Reply:

To install a 7-Way harness on your 2023 Subaru Outback you will need two separate wiring harnesses because they don't make just one that'll do the job.

The first harness you'll need is the Curt T-Connector Vehicle Wiring Harness item # C56040. This custom-fit T-connector plugs into your Subaru's wiring harness, which is in your rear cargo area. This will provide you with a 4-flat connector.

The second harness you will need is the Universal Installation Kit for Trailer Brake Controller item # ETBC7. The kit includes a pre-wired 7- and 4-way trailer connector that mounts easily at the rear of your vehicle with an included bracket. This kit is designed for use on a vehicle with an existing 4-way flat trailer connector and plugs directly into it.

Some other parts you will need to tow a trailer with your 2023 Subaru Outback are listed below:

Trailer Hitch - Curt Trailer Hitch item # C67JR

Wiring Harness Mount - No-Drill Mount Bracket item # 18136

Brake Controller - Redarc Tow-Pro Liberty Brake Controller item # RED24FR and Wiring Adapter item # RED69FR

Ball Mount - Curt Towing Starter Kit for 2" Hitches item # C45534

expert reply by: Jerred H

0

Answer 1

That's an interesting question, and yes, you can use your older phone as a kind of dedicated brake controller with the Curt Echo Wireless Trailer Brake Controller #C51180. The phone will need to have the app downloaded so you'll need…

view full answer...

Answer 2

There is indeed a trailer hitch receiver that fits your 2024 Subaru Crosstrek Wilderness, from Curt, with the correct part number being the following: - Curt Trailer Hitch Receiver #C13382 I verified this fit with the manufacturer for you, and it…

view full answer...

Answer 3

Yes, a standard manual brake controller wire can be routed in your 2021 Subaru Outback Wagon with a Universal Installation Kit for Trailer Brake Controller #ETBC7. The wires will need to be in your cabin. While it is not required to run the backup…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

It makes perfect sense, and I completely agree with you Chris! The wiring manufacturers tell people to drape it over the tailgate as a simple solution, but the clean look and readily available access makes mounting the 4-Way connector next to your…

view full answer...

Answer 7

The best hitch for a 2024 Subaru Outback is the etrailer item #e25TR. This hitch is custom fit and bolts to your Subaru with included hardware. This is a class III hitch with a 2" receiver, that has a 3,500 lbs towing capacity and a 350…

view full answer...

Answer 8

The Curt #C13410 and Draw-tite #76227 are very similar in design and both have the same weight ratings of 600lbs tongue weight and 4,000lbs of trailer weight. I do like that Draw-Tite does add the additional plate of steel in between the hangers…

view full answer...

Answer 9

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 10

The etrailer axle part #e82GR can only be installed in an underslung orientation. Since the axle has a bow to it if you were to flip it the alignment would be way off. You'd have to weld spring seats on the opposite side of the axle with the…

view full answer...