Does Reese RP30154 Rail Kit Adapter Work with 50008 Slider

Question

Question:

Will the Reese 5th Wheel Rail Adapter for Ram OEM 5th Wheel Towing Prep Package - 25,000 lbs Item # RP30154, fit Reese 18K round tube slider Part#50008 Thank you,

asked by: Damond

1

Helpful Expert Reply:

Yes, the Reese fifth wheel rail kit adapter part # RP30154 does work with the older Reese Select Plus 50008 slider base you mentioned.

expert reply by: Jameson C

1

Answer 1

The Reese #50008 is the part number corresponding to a round tube slider unit (the slider, but not the hitch) that is no longer being manufactured. According to my contact at Reese, their part #58161 is the correct replacement actuating handle for…

view full answer...

Answer 2

The measurements between the front and rear holes on the Adapter Rails for Curt 5th Wheel Hitch #C88KR are 20 1/2" center on center, and 29" center on center. These holes are spaced for the industry standard 5th wheel mounting…

view full answer...

Answer 3

Yes, the older version of the Reese round tube slider for 5th wheel hitches, 50008, will fit in the rail adapter, #RP30154, for Rams with the OEM tow package. I have included a link to the installation details for you to view.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...