Troubleshooting Powered Lift Not Working on Fan-Tastic Vent Roof Vent

Question

Question:

Have a 3301 fan-tastic fan which only works when manually opened and then manually closed. However the rain sensor does work as it should. Do I need to replace the whole thing or??

asked by: Bob I

0

Expert Reply:

It sounds like the powered lift is no longer working on your Fan-Tastic Vent roof vent. More than likely the motor has gone bad and replacing it will solve your problem. You can use the # FVK6010-81 for white or the # FVK6010-80 for off-white.

expert reply by: Robin H

0

Answer 1

Good news! I was able to track down two 17 RPM fan lift motors to replace your original Fan-Tastic Vent motor. I spoke to my contact at Fan-Tastic Vent and she informed me that the 7RPM replacement would work, but would move very slowly, it's…

view full answer...

Answer 2

Since everything works aside from the power lift, and the motor didn't fix the problem, I would say it is a bad control board. You could certainly test the switch for power if you want, but it isn't available as a separate replacement. The…

view full answer...

Answer 3

Have you tried reprogramming the remote? For programming a Fan-Tastic roof vent remote like part #FV9068-09 which is what your 7350 fan part #FV807350 uses what you need to do is hold your remote 12 inches away from the fan while holding both arrows.…

view full answer...

Answer 4

The number ( 411 D) you provided doesn't correspond with a Fan-Tastic Vent roof vent model number, but if yours uses the remote control #FV9068-09 that you referenced, that tells us it's a 7350 Series Fan-Tastic Vent Roof Vent, like…

view full answer...

Answer 5

I wish we could get what you need but apparently it's old enough our current options won't work. This means that you're going to have to upgrade to the Fan-Tastic Vent Roof Vent w/ 12V Fan and Remote #FV807350 to have a functional roof…

view full answer...

Answer 6

The only way to get the replacement circuit board for your Fan-Tastic Vent Roof Vent is through part #FV807359, which is essentially all the main internal components, including the circuit board, screen assembly, powered lift, as well as a new remote…

view full answer...

Answer 7

In order to then enable the rain sensor on the Digital Remote Control #FV9068-09 you need to hold the up/down arrow on the remote for three seconds until you see the light illuminated under the "Rain Sensor Off" label disappear. Please note…

view full answer...

Answer 8

Since you held down the arrows I'll assume you did it a foot away from the #FV807350. The Auto and Manual lights should begin flashing immediately, followed by all seven LED's flash once. This indicates it is programmed. You could also make…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...