How Thick is the U-Bolt Plate for 3-1/2 Inch Diameter Round Trailer Axles

Question

Question:

Do you have the steel thickness on this plate?

asked by: Kris

1

Helpful Expert Reply:

The U-Bolt Plate for 3-1/2 inch Diameter Round Trailer Axles # 117581 is 1/4 inch thick.

expert reply by: Michael H

1

Answer 1

There is no specific torque rating for shackle bolts. Basically for the middle bolt there should be enough free play in the shackles to allow them to move. Tightening the shackle bolts too much will squeeze the shackle straps against the leaf springs…

view full answer...

Answer 2

The distance between the holes of the U-Bolt Plate part #117581 are 3-1/2 inches long ways and 2 inches short ways measured from closest part of the hole to closest part of the other hole since this is designed to fit a 3-1/2 inch diameter axle and a…

view full answer...

Answer 3

When looking at equalizers for your trailer's suspension, anything at or over an inch in difference will most likely cause some issues with the overall suspension, especially if nothing else is being replaced. To replace your original equalizers,…

view full answer...

Answer 4

There should be enough free play in the shackles to allow them to move. There is no specific torque rating for shackle bolts. The first thing you should make sure of is that the bolts you use are long enough so that when installed you will have at…

view full answer...

Answer 5

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

How Thick is the U-Bolt Plate for 3-1/2 Inch Diameter Round Trailer Axles

Product Page this Question was Asked From

Continue Researching